RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: December 19, 2018, 05:29:46 PM »
kamalsahai
Plane Lover
Forum Veteran
****

Reputation Power: 8 
kamalsahai has no influence.
Offline Offline

City: chandigarh
State: Chandigarh
RC Skills: Beginner
Posts: 457
Join Date: Sep, 2014




KINDLY INTIMATE LOCAL SOURCE OF  PUSH ROD FOR 9 GRAM SERVO TO BE INSTALLED ON SKY SURFER

REMEMBER IT SHOULD BE SOFT AS COMPARE TO STANDARD PUSH ROD

HOPING FOR REPLY

KP

Logged
 

Read
« Reply #1 on: December 19, 2018, 07:35:56 PM »
AL HAM SHARI
^^^^^^^^^^
Plane Lover
Forum Hero

*****

Reputation Power: 7 
AL HAM SHARI has no influence.
Offline Offline

City: Alappuzha
State: Kerala
RC Skills: Beginner
Posts: 535
Join Date: Nov, 2012

RC



I normally use Umbrella Frame rod as pushrod. You could get it for free from junkyards ( if the owner isn't a greedy sob.) It fits perfectly with that thingy ath the end of a pushrod (can't exactly remember it's name.) It's flexible but not bendy.
Logged

☮️
 

Read
« Reply #2 on: December 19, 2018, 09:04:52 PM »
pnkyjs
Plane Lover
Senior Member
***

Reputation Power: 3 
pnkyjs has no influence.
Offline Offline

City: Satara
State: Maharashtra
RC Skills: Intermediate
Posts: 198
Join Date: Apr, 2010



thats good umbrella spokes, some use bicycle spokes too, I use a higher grade or thicker binding wire found at the hardware store
Logged

V911
V977
XFX 450 V2
Scratchbuild foamies galore
 

Read
« Reply #3 on: December 19, 2018, 09:07:30 PM »
pnkyjs
Plane Lover
Senior Member
***

Reputation Power: 3 
pnkyjs has no influence.
Offline Offline

City: Satara
State: Maharashtra
RC Skills: Intermediate
Posts: 198
Join Date: Apr, 2010



but if you are forced to use flexible wire, then encase it inside some thin pipe like a drinking straw, and tape the pipe well onto the fuselage or wing.
Logged

V911
V977
XFX 450 V2
Scratchbuild foamies galore
 

Read
« Reply #4 on: December 20, 2018, 08:37:55 AM »
shirsa2001
Plane Lover
Senior Member

***

Reputation Power: 2 
shirsa2001 has no influence.
Offline Offline

City: Pune
State: Maharashtra
RC Skills: Intermediate
Posts: 169
Join Date: Sep, 2017



There should be a hardware market in your city with a shop that stores all kinds of metal wires.
Ask them to show you wires of gauge around 1mm (give or take).
Check if the gauge and flexibility suits sky surfer. That should work.

The shiny hardened steel wire that comes with sky surfer is hard to find if not sold by rcbazaar.
If you have access to a paper clip manufacturer/supplier you can try that.
Logged
 

Read
« Reply #5 on: December 20, 2018, 11:40:42 AM »
sanjayrai55
Plane Lover
Forum Hero

*****

Reputation Power: 74 
sanjayrai55 has a powerful will.sanjayrai55 has a powerful will.sanjayrai55 has a powerful will.sanjayrai55 has a powerful will.sanjayrai55 has a powerful will.sanjayrai55 has a powerful will.sanjayrai55 has a powerful will.
Offline Offline

City: Gurgaon
State: Haryana
RC Skills: Intermediate
Posts: 7228
Join Date: Dec, 2011

Don't wake a Tiger until you've factored the teeth



The only correct solution is Google for Spring Manufacturers in your town. Go their place, and request them to give you a piece of 0.8 or 0.9 mm Spring Steel wire

Use Linkage stoppers, or make a Z Bend with a nose pliers
Logged

Sanjay - Gravity is my enemy
 

Read
« Reply #6 on: December 20, 2018, 03:03:40 PM »
tictoc21
Heli Lover
Forum Veteran

****

Reputation Power: 6 
tictoc21 has no influence.
Offline Offline

City: mumbai
State: Maharashtra
RC Skills: Intermediate
Posts: 402
Join Date: Jun, 2015



This one

rps20180729_121731.jpg
Re: LOCAL SOURCE OF CONTROL PUSH ROD FOR 5 GRAM OR 9 GRAM SERVO
* rps20180729_121731.jpg (31.18 KB, 734x734 - viewed 105 times.)
Logged
 

Read
« Reply #7 on: December 20, 2018, 03:04:02 PM »
tictoc21
Heli Lover
Forum Veteran

****

Reputation Power: 6 
tictoc21 has no influence.
Offline Offline

City: mumbai
State: Maharashtra
RC Skills: Intermediate
Posts: 402
Join Date: Jun, 2015



This one is steal wire which hard and flexible enough.
Hard when used for short length and flexible when used for long length.
You can find it in hardware store or electrical store.
Please remember there is another wire available for centring which is made up of soft metal. This one is steal wire available in large shape rings.
Ask for hard steal wire. And remember as it is steal wire it has rust on it.
The only problem with this wire is to make it straight for any application. You have cut it to desired length and use FLAT head hammer to make it straight.it need some time after hammering properly you will get straight wire hard and enough flexible through it.
Use only flat head hammer curved head will not work properly.
And last this you must need lot patience to make it straight.
For glider type craft you will need a narrow bore pipe to work wire properly.
Logged
 

Read
« Reply #8 on: December 20, 2018, 09:04:28 PM »
kamalsahai
Plane Lover
Forum Veteran
****

Reputation Power: 8 
kamalsahai has no influence.
Offline Offline

City: chandigarh
State: Chandigarh
RC Skills: Beginner
Posts: 457
Join Date: Sep, 2014



thanks for information and guidance

kp
Logged
 

Read
« Reply #9 on: December 20, 2018, 10:42:46 PM »
rastsaurabh
Plane Lover
Forum Hero

*****

Reputation Power: 19 
rastsaurabh has no influence.
Offline Offline

City: Noida
State: Haryana
RC Skills: Intermediate
Posts: 1553
Join Date: Mar, 2012



how to make wire straight.

Logged
 

Read
« Reply #10 on: January 10, 2019, 11:44:43 PM »
K K Iyer
Global Moderator
Forum Hero
*****

Reputation Power: 48 
K K Iyer might someday be someone...K K Iyer might someday be someone...K K Iyer might someday be someone...K K Iyer might someday be someone...
Offline Offline

City: Indore
State: Madhya Pradesh
RC Skills: Intermediate
Posts: 4071
Join Date: Jan, 2012



Found something that may meet your requirements.

Wire from roomheater. Looks similar to the curved pushrods from central servo to ailerons on my Yak.

And earbud for outer tube.

Hope this helps


image.jpg
Re: LOCAL SOURCE OF CONTROL PUSH ROD FOR 5 GRAM OR 9 GRAM SERVO
* image.jpg (46.16 KB, 800x600 - viewed 52 times.)
Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
wanted used three 9 gram servos
Wanted
vineet 4 1488 Last post October 12, 2013, 10:28:17 PM
by streetjerk
24 gram hextronik motor
Wanted
kaarthic.r.b 1 1143 Last post June 25, 2013, 09:49:35 PM
by kaarthic.r.b
4 nos 9-gram servos
For Sale
buzz_rc 3 1619 Last post September 18, 2013, 10:13:10 AM
by buzz_rc
9 gram servo for sale !!
For Sale
streetjerk 15 2759 Last post October 13, 2013, 05:30:13 PM
by AnjanBabu
Cys 9 gram servo brand new for sale 125 Rs + shipping
For Sale - Completed
Vasudev 0 297 Last post August 24, 2017, 04:20:08 PM
by Vasudev