|
Title: need help with diy simulator cable Post by: Priyanshu@ on October 25, 2017, 04:36:37 PM hello every one
currently i am working on simulator cable i have made it too with aux cable and some jumper wires . even i double checked connections but it is correct . with smartpropoplus software in my laptop(win 10) it is not showing any ppm output. and in my pc (win 7) its showing ppm output but showing vjoy device missing . what should i do or do i need dongle adaptor or if any one selling used simulator need help . :help: :help: whatsapp ; 9033722997 Title: Re: need help with diy simulator cable Post by: prabal276 on October 25, 2017, 08:19:53 PM Do you have vjoy installed?
Is it giving any readings? If you manage to find realflight G4.5 somewhere, I can email you the dongle emulator software. Title: Re: need help with diy simulator cable Post by: Priyanshu@ on October 25, 2017, 09:14:45 PM thanks Prabal sir for the reply
as in my laptop having only single aux jack of headphone no one for mic. Thus it was having no ppm input. And as my pc runs on win 7 it was unable to fullfill the requirements of vjoy thus it didn't installed properly. ( I didn't recognise that earlier). But I checked this on my friend pc after some efforts it worked but only the problem is the rudder stick is not calibrated. Sir do you or anyone knows how to make laptop single headphone jack works as a mic jack to receive input. Regards Priyanshu Title: Re: need help with diy simulator cable Post by: prabal276 on October 26, 2017, 04:40:47 AM I'm not a "sir"!
There are some adapters that are available commonly. They plug into the single 3.5mm audio jack. They have both line in and line out. Get one of them. Vjoy is perfectly compatible with Windows 7. I run it on my Win 7. Regards Title: Re: need help with diy simulator cable Post by: prabal276 on October 26, 2017, 04:45:38 AM You need something similar:
https://m.ebay.com.au/itm/371870570556?_mwBanner=1 Title: Re: need help with diy simulator cable Post by: Priyanshu@ on October 26, 2017, 06:49:09 AM Okk thanks .
I will try to get the splitter cable and than try Title: Re: need help with diy simulator cable Post by: Priyanshu@ on October 26, 2017, 10:31:18 PM Ok thanks
It works on my pc I upgraded the win to win8 and it works I am having multiflight simulator but don't know how to calibrate the sticks only rudder stick is uncalibrated. Any suggestions for a downloadable good simulator Thanks and regards Priyanshu Title: Re: need help with diy simulator cable Post by: prabal276 on October 27, 2017, 06:55:25 AM Better get the all in one sim from bangoood.
Regards Title: Re: need help with diy simulator cable Post by: MakerHand on October 27, 2017, 08:44:32 AM Just give me a working simulator software link, then I think, I can help :banghead:
Title: Re: need help with diy simulator cable Post by: tictoc21 on October 27, 2017, 01:19:04 PM Hi friends i have FMS sim cable is there any software that it will work with pheonixrc simulator...???
Title: Re: need help with diy simulator cable Post by: Priyanshu@ on October 27, 2017, 05:24:48 PM @Makerhand
As my simulator cable is diy and without any dongle so I am using vjoy with smartproplus software available for free. And I am having multiflight simulator Need help with calibration of rudder stick Thanks and regards Priyanshu Title: Re: need help with diy simulator cable Post by: prabal276 on October 27, 2017, 05:26:45 PM Priyanshu, aren't you having a 3.5mm jack on your transmitter?
Title: Re: need help with diy simulator cable Post by: Priyanshu@ on October 27, 2017, 05:29:45 PM On transmitter I am having svideo port .
I am having flysky FS i6x tx It don't have 3.5 mm jack on it Title: Re: need help with diy simulator cable Post by: Priyanshu@ on October 27, 2017, 05:36:17 PM I connected ppm output to signal of aux cable and base to base. Of svideo cable to aux cable
Title: Re: need help with diy simulator cable Post by: MakerHand on October 28, 2017, 09:31:46 PM @Priyanshu
I hope this video will help you... https://youtu.be/66ewuz9RPv4 |