Title: Newbie Help needed for scratch built RC plane Post by: rprithvir on May 21, 2014, 08:00:59 PM Hi all
Im new to RC india , i have good knowledge on gliders but im new to rc aeromodeling once i had GUANLI A10(http://www.zs-gl.com/1/en/productshow.asp?id=32&sortid=1 (http://www.zs-gl.com/1/en/productshow.asp?id=32&sortid=1)) model plane which crashed but i managed to recover all parts electronic parts and transmitter. now what i have is 9.6v-650MAH NI-MH battery Power:twins 55 duct fan(370 brush motor) 4channel TX and RX. 3 9g servo, 140A brush ESC all in good working condition i like to built a new rc plane with these parts . Please suggest me how to start.... could these parts can be used to built propeller type plane? please help Title: Re: Newbie Help needed for scratch built RC plane Post by: Swapnil on May 21, 2014, 08:07:47 PM You can certainly re-use those parts to build a new plane. But it would be much easier to upgrade to a LiPo powered brushless system.
Title: Re: Newbie Help needed for scratch built RC plane Post by: rprithvir on May 21, 2014, 08:22:19 PM thanks for immediate reply
im i searched over net for replacement and upgrades but point there is no brand name or spec on the motor so i could look for same powered motor :o and more over motor i have has only 2 terminals but brushless motor on net have three terminals :headscratch: Title: Re: Newbie Help needed for scratch built RC plane Post by: Swapnil on May 21, 2014, 08:37:37 PM Here's something from the bottom of the 'GUANLI A10' page (the link you posted):
Brushless Version WINGSPAN : 872mm LENGHT : 968mm WEIGHT : 450g BATTERY : LI-PO BATTERY 11.1V-1000mAh POWER SYSTEM : two sets of C2410 burshless motor power system RADIO SYSTEM : 4CH RC system . 3 servos . 2pcs 25A brushlessed ESC Brushless motors need a 3-phase supply and hence have 3 wires. Title: Re: Newbie Help needed for scratch built RC plane Post by: sundaram on May 22, 2014, 12:21:05 AM Along with it you will need a brushless ESC with three phase out put in place of brushed ESC.
Title: Re: Newbie Help needed for scratch built RC plane Post by: Swapnil on May 22, 2014, 06:05:53 AM You could also use your brushed setup with a LiPo. But, before you start with anything, please go through as much information as you can regarding RC electronics and construction.
Title: Re: Newbie Help needed for scratch built RC plane Post by: rprithvir on May 23, 2014, 11:42:49 AM You could also use your brushed setup with a LiPo. But, before you start with anything, please go through as much information as you can regarding RC electronics and construction. thanks for your idea first i learn some more about RC electronics 8-) Title: Re: Newbie Help needed for scratch built RC plane Post by: rprithvir on May 27, 2014, 12:54:29 PM can any one suggest a propeller if my plane weights 500 grams with 9.6v-650MAH NI-MH battery
370 brush motor 4channel RX and 3 9g servo,40A brush ESC Title: Re: Newbie Help needed for scratch built RC plane Post by: ajn9325 on May 28, 2014, 01:16:04 AM Check the motor specifications, the recommended prop sizes would be mentioned there. :thumbsup:
Title: Re: Newbie Help needed for scratch built RC plane Post by: rprithvir on May 28, 2014, 12:01:40 PM there is no specificatons on manual with the stock motors
Title: Re: Newbie Help needed for scratch built RC plane Post by: ponappa on May 28, 2014, 01:21:55 PM This is a Ducted fan motor with ducted fans. Cant use props. You can get a A-10 from
http://rcbazaar.com/products/614-a-10-thunderbolt-warthog.aspx (http://rcbazaar.com/products/614-a-10-thunderbolt-warthog.aspx) and you fix the parts. All the Best with your flight. |