RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: December 05, 2018, 02:32:43 PM »
veera
Car Lover
Active Member
**

Reputation Power: 1 
veera has no influence.
Offline Offline

City: coimbatore
State: Tamil Nadu
RC Skills: Intermediate
Posts: 6
Join Date: Jul, 2014

I love to fly <3




Hello all.... I have an eachine 250 pro with F3 board...the issue i face is the drone is not flying after 3 or 4 flights after the bootloader works are done and saved those in F3 board ....i am using a cleanflight v 1.2.4 which i did after watching some youtube videos ....please help me in this....some time one of the motors is not running ...sometimes all four working good....!
Logged
 

Read
« Reply #1 on: December 05, 2018, 08:57:40 PM »
newpg202
Plane Lover
Senior Member
***

Reputation Power: 1 
newpg202 has no influence.
Offline Offline

City: NORTH 24 PARGANAS
State: West Bengal
RC Skills: Intermediate
Posts: 105
Join Date: Oct, 2018



Calibration of ESC is needed perhaps.

Sent from my Mi A1 using Tapatalk
Logged

Qads: S500, F450, Robocat 250, GH160
Helis: XK K120, Trex 450, Alzrc X360, Alzrc Devil 380, Agile A5
Plane: FT mini Scout
 

Read
« Reply #2 on: December 06, 2018, 09:44:25 PM »
veera
Car Lover
Active Member
**

Reputation Power: 1 
veera has no influence.
Offline Offline

City: coimbatore
State: Tamil Nadu
RC Skills: Intermediate
Posts: 6
Join Date: Jul, 2014

I love to fly <3



How to do that???now the problem is my drone is not responding my commands☹️
Logged
 

Read
« Reply #3 on: December 06, 2018, 11:25:43 PM »
sim_tcr
Car Lover
Forum Veteran

****

Reputation Power: 5 
sim_tcr has no influence.
Offline Offline

City: Thrissur
State: Kerala
RC Skills: Intermediate
Posts: 311
Join Date: Jan, 2018



How to do that???now the problem is my drone is not responding my commands☹️
Connect the FC to computer, keep the battery disconnected.,
In configurator go to Motors tab
Enable, I understand the risk,
Move the master slider to maximum position and connect the battery. Once the beeps are completed, lower master to zero and ESCs will finish their tones.
Disconnect the battery and connect again. Raise Master very slowly until the motors are spinning comfortably. Make a note of the value this is at.
In Configuration tab,change Min Throttle to about 20 points greater than the value you noted earlier.
Hit Save and Reboot.
Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
Another newbie here..
Multirotors
hypd09 3 2686 Last post November 13, 2012, 12:34:02 AM
by anand21nanda
X3 Newbie
Helis
Cary101 6 4112 Last post December 05, 2012, 03:55:37 PM
by raja_mastana
Need help for a newbie
Beginners Zone
v2 eagle 4 4553 Last post August 04, 2013, 09:10:24 AM
by rcrcnitesh
I'm a newbie,So please help me!!!
Beginners Zone
Aravind298 9 5800 Last post April 27, 2016, 03:25:37 PM
by SI74
Newbie
Tools, Materials and Building Techniques
Wassiriour1942 1 2175 Last post May 12, 2016, 01:45:22 PM
by prabal276