This Plane is made up of cardboard and thermocoal its about 1 kg i m using 1900 kv motor with 7 x 4 prop and 30 amp esc and 2200 mah 11.1 volt 3s lipo battery is everything right on it .the transmitter i m using is avionic rcb6i rx and tx help guys

specify what kind of help you want, so that someone can approach you.

anyway congrats on your first build and all da best, cheers

Hi, weight is too much, should be about 600g for a foamy

What's is the wing span

Hi Priyamraj

Glad to see u here.
Your electronic combination are good and more than enough to take ur model to sky.
Give some more detail about your model wing span and cord, fuselage length,  motor thrust.
only with the proper aerodynamics you will able to fly.And yes 1kg is too much respectively to ur plane,
Congrats for ur 1st model

friend ;
Pl. post the plans you followed , And the AUW mentioned on the plane.
And what kind of wing do you have? Flat bottom......airfoil..........etc. etc.?

THE WINGSPN IS 35 INCHES and its breadth is 20 cm this pleane is a copy of maker trainer 2 the wing is in airfoil shape and the motor's thrust  is 1200 gm at 22600 rpm and 7 x 4 propeller i just wantted to ask will it fly the wing is made up of thermocoal with 2 . 0 mm carbon rod 

that blue one is not my plane it is maker trainer built by lucias weakley

Hi Guys ,
i have made my first rc plane i just wanted to know will it fly ?
specifications-
motor - avionic 1900kv c2826
esc - avionic 30 amp
prop. - 7 x 4 E (i also have 8 x 3.8 E )
battery -wolfpack 11.1v 25c 2200mah lipo pack
servos - two avionic 9g servos  , one avionic 12 g servo
receiver - avionic rcb6ch
transmitter - avionic rcb6i
battery charger - robomart balance charger for 11.1 volt  and for 7.4 volt


now some hardwares -
wing material -  thermocoal with 2 . 0 mm carbon fibre rod
wing span - 32 inch
material used in fuselage , elevator , tailboomps , stabilizers - cardboard boxes
Gross Weight 1.1 kg
i have covered the wing and some areas which are white with paper and fevicoal


thanks 
i hoope u will help soon and please because  i have iinvested rs 10000 on it  and uploaded some pictures

According to the website,
PROP – 8x4E
● Get 1200gms Thrust
Lipo – 3cell 11.1V
Operating Voltage – 10.3V
Amp draw at load – 33amp
ESC - 40 amp
Power –330W


So technically this should fly your plane good .. very good and very fast in fact but you need to get a bigger ESC.. the amp ratings at max is 33 amps which exceeds your 30 amp esc ratings.. I'd say you go with a 50AMP ESC with a 8 inch prop on it.

Also, Do a range check before you fly your plane. It's absolutely necessary with your transmitter.

Thaanks but i dont have money now  how much thrust will 7 x 4 prop produce is it well with 30 amp esc ?

Hi Guys ,
i have made my first rc plane i just wanted to know will it fly ?
specifications-
motor - avionic 1900kv c2826
esc - avionic 30 amp
prop. - 7 x 4 E (i also have 8 x 3.8 E )
battery -wolfpack 11.1v 25c 2200mah lipo pack
servos - two avionic 9g servos  , one avionic 12 g servo
receiver - avionic rcb6ch
transmitter - avionic rcb6i
battery charger - Robomart balance charger for 11.1 volt  and for 7.4 volt


now some hardwares -
wing material -  thermocoal with 2 . 0 mm carbon fibre rod
wing span - 30 inch
Wing Breath - 20 cm
material used in fuselage , elevator , tailboomps , stabilizers - cardboard boxes
Gross Weight 1.4 kg
i have covered the wing and some areas which are white with paper and fevicoal


thanks  
i hoope u will help soon and please because  i have iinvested rs 10000 on it  and uploaded some pictures






is everything fine like esc and other dont tell me buy other

This is the plane which i have followed well i cant get foam boards i dont think they are anywhere is jharkhand

Well a 30 inches span plane should not weigh above 500-600 gms.  With this construction.... anybody's guess.........

My dear friend... why are you creating 3 separate threads on the same plane ?  Please understand that is totally confuses people, and floods the forum with repetitive information.

Merged