RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: January 05, 2016, 09:26:49 AM »
sagar.rv.712
Plane Lover
Active Member
**

Reputation Power: 1 
sagar.rv.712 has no influence.
Offline Offline

City: BANGALORE
State: Karnataka
RC Skills: Beginner
Posts: 1
Join Date: Jan, 2016




guys please help me out of this. i want to built  an r.c plane ? what will be the cost for a basic model of an r.c plane?  Huh?
Logged
 

Read
« Reply #1 on: January 05, 2016, 09:56:45 AM »
Sukhpreet
RC Learner and a lover
Plane Lover
Senior Member
***

Reputation Power: 3 
Sukhpreet has no influence.
Offline Offline

City: Chandigarh
State: Chandigarh
RC Skills: Beginner
Posts: 236
Join Date: Dec, 2015



* Building material (depron or thermocol or epp or epo or coroplast) Most of these are not available (Check out http://www.kinetichobbies.com/) , (RCDhamaka.com), (RCBazaar.com)

* Building plans (Start from easy first. Search for trainer models like blue baby or Sky King) (A high wing slow aircraft should be ur preference as it will give you ample of response time)

********Electronics*********
* 1 Brushless motor and a prop (It could be a pusher or a puller) (RS 500+)
* Esc for motor. It should be atleast 5-10 amps more than the need of the motor (RS 500+)
* 2 or 3 Servos To control control-surfaces(Ailerons/rolling, elevators/pitch/Going-up-down and rudder) (Rs 170+ per motor)
* lipo battery and charger. Be carefull with the battery (depends on the weight of aircraft and power required because high capacity will be higher in weight. and carrying higher weight will be inefficient So it wont increase ur flying time too high)

* Transmitter and a receiver(atleast 6 channels) (Most important) (Starts from RS-2850/- Flysky CT6B) But as per forum people go for Futaba Or JR(expensive ones)

*******hardware**********
* Cutting knives and blades (rs 160+)
* HOT GLUE (400rs for hot glue gun and rs 10 to rs 15 for hot glue sticks)
* Packing tape(Give a coating to ur aircraft using this for extra strength) rs 85 to 500 rs
* Push rods to connect servo motors and control surfaces using CONTROL HORNS(rs 35 to 70 for 5-6 push rods and rs 25+ for control horn per peice)

Lots of patience

And knowledge and passion. Start watching Flitetest videos Beginner Series. And "Maker Hangar" on youtube

And also search for CG ie Center of gravity(Dont know much about how to calculate this. even i am doing R and D on it)

Sometimes you will need to solder a few things. So get a soldering setup as well
You may need to be careful about the connectors

Hope these points will help. Smiley
(And pls do R and D on above points to get better picture of what i am saying)
« Last Edit: January 05, 2016, 10:13:46 AM by Sukhpreet » Logged

F-450 Quadcopter With KK 2.1.5 and FPV capability, FS-CT6B

And remember #FlyLikeAButterflyStingLikeABee
 

Read
« Reply #2 on: January 05, 2016, 07:33:40 PM »
SI74
Plane Lover
Forum Hero
*****

Reputation Power: 7 
SI74 has no influence.
Offline Offline

City: Muvattupuzha
State: Kerala
RC Skills: Beginner
Posts: 561
Join Date: Jun, 2015



For a Beginner only.
If you have around 2500 Rs other than the costs of building tools and TxRx, you can make one.
1.Motor = 600  to 950 Rs
2. Esc - 600 to 950 Rs
3. Lipo - 300 to 500 Rs
4. Servos - around 200 each
5. Landing Gear - Around 160 Rs
6.Bullet connectors*3 and heat shrink tube - around 250 Rs
7.Propeller -80 Rs
8.If depron 200 + If Thermocol around 100
------------
TxRx- 2600 and up
------------
Building tools including Hot Glue Gun
Logged
 

Read
« Reply #3 on: January 05, 2016, 07:36:37 PM »
SI74
Plane Lover
Forum Hero
*****

Reputation Power: 7 
SI74 has no influence.
Offline Offline

City: Muvattupuzha
State: Kerala
RC Skills: Beginner
Posts: 561
Join Date: Jun, 2015



"Slowly " is another very good beginner model.

Turnigy 5Ch TxRx ( costs around 2700 Rs) is  very good for a beginner ( 1.Very easy manual programming of channels at the flick of a switch  2. Light weight even a kid can carry  3. Needs only 4 rechargeable batteries which lasts much longer than in a Flysky )
« Last Edit: January 05, 2016, 07:51:20 PM by SI74 » Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
Basic's of Building plane
Tools, Materials and Building Techniques
praveen 2 4244 Last post September 10, 2010, 12:09:42 PM
by praveen
coroplast basic model
Electric Planes
abhijeetvit 13 8108 Last post April 16, 2013, 07:50:16 PM
by vishalrao
Basic foam built trainer model build log.
Electric Planes
johnywalker8pm 18 11684 Last post March 16, 2014, 11:09:14 PM
by johnywalker8pm
Want a 6Ch basic radio and a Basic 3S 4S balance charger
Wanted
sooraj.palakkad 2 1796 Last post February 24, 2015, 08:03:33 PM
by radiocraft
Help me building basic nitro plane
Gas/Glow/Nitro Planes
prashantwairagade 5 3347 Last post May 10, 2019, 08:29:22 PM
by unidrakeshrc