my first boat.. ..
i try to builde rudder at self.. hope so it work propperly ....
-use 1000kv out runner motor with 25amp esc ..
-9grm servo
-i will use 2s or 3s battery..

for esc cooling system i use 3mm aluminium small pice.
which i attach to boat bottom part... so it will cooling down direct from the water ...
no need pipeing stuf...and also use out runner motor..
still final finishing remaining..

nice work nic.......

Thnk you madaquif...... 

Nice boat... if it is your first boat then its a great one...

Welcome aboard Matey! Nice one there.

Yup topalle ... I m new in rc ... So I try to builde...

Hello vc...
Ur a boat lover ..can u suggest me  so Wht to do .. or is Thr to do any change in ths model ..

Nik, a little suggestion - since you say you are new to the forum, please refrain using sms lingo. That is one thing that upsets our moderators. 
Hope you don't mind.

Hmm sorry essaargee ... But I did not understand Wht you are talking about...

Nik, the boat looks fine, maybe you want to add a topside to it and detail it a bit. Have you sailed her as yet? Is he balanced?

What essaargee was trying to tell you is that abbreviated English, lik this u kno wht i mean, is not appreciated here and that you are requested to communicate in the expanded version of the language.

Yes vc I checked a balance .. it's balance properly..
And yeah I use a top cover...
Some painting and detailing is remain..

Opps sorry ... I understand  vc and essaarge... Thank you ..

   good start. Keep it up buddy.

Thank you gajjark....
Hope so it will work good...

Any one suggest me  ,which Type of filler should I use for outer boady finishing.
Which is easy available in Market...

Nice Build Nik... Do put up turn Fins on this one.

You can use NC PUTTY for outer body finishing and it is easily available in automobile body paint shop

Thank Rooster ..
Sorry But I dont know what is a turn fins?
Can you tell me.

Okk gaurang ... I will do that ..

this pictures shows you what is turn fins?

Okk gaurang I got it ..  
But in image one you send me turn fins... In this left and right fin both fins are in different
Length...
Is this both are in equal Length or diferente?

Keep in mind it's a single prop boat which will always turn better to the right, left hand turns at speed should be wider, after all, all races have only right hand turns in competition if u prefer left turn than make bigger turn fin for left and smaller for right side and u can also install one turn fin also

Aaaahhaa... Now I deeply understand the use of turns fins... Thank you Soo much gaurang... 

always welcome nik

after a finishing ..using NC putty..
and attach turn fins.
now ready for painting.

finaly painting  done... 

Very nice 

Waiting for the video 

Yup I will upload Very soon...

Looking good! Waiting for the maiden................

Put on some stickers from an Automobile deco shop and make her look even better.

  looks good

very good work nik

Thank you to every one...
yup VC .. thats the batter idea... 

any one tell me .. what should i do for an electronics water proofing

Put the electronics in an airtight box. Cut/melt holes for wires. pull the wires and fill the hole with waterproof m-seal. hope that should do.

Azad

For ESC.. Cut open the Black heatshrink on the ESC. Remove the heatsink... it is is the aluminium plate.. Mix araldite regular( not the Clear 10 minutes). Apply it on the entire ESC. do not leave any open spots on the ESC. then take a wooden icecream spoon and scrape out the entire Araldite on the surface of the small black components that will be in contact with the heat sink. you can use a cloth to wipe the surface. Ensure that you only wipe the surface.Replace the heatsink and use a couple of rubberbands to hold in position.
for RX-Put the RX in a large balloon and wrap the mouth of the ballon with a cello tape.
For Motor there is nothing requried.
Battery: Can take a little water.Needs to be dried before use after it is wet. Although can cause corrosion issues in the long run. You can use a couple of ballons on the battery as well.


Shreekant

Thank you topalle...
Rooster thats the Nice trick ... 

Rooster is there Any problem If water come inside the motor?

nik i think this link answers your question
http://www.rcindia.org/boats/submarine-and-amphibian-lovers-brushless-works-under-water-!!!/msg93028/#msg93028

My boat first run... Awsome Sunday.. great fun with my boat... 

Watch "Home made rc boat. First Run" on YouTube -

Thanks to Every one .. WHO support me to build thase boat ... Thank you friends.....  

congrats Nik very good 

Thank you gaurang... Your típs about fins and turning If perfect...   

Very nice. Agile sailor!

Yup vc... 

hi where i will get the rc boat shaft and prop

I had ordered prop and shaft from banggood.com... its been like a month now yet to receive it...could'nt find any in LHS..

Check on to the below mentioned link.

http://www.muav.in/?wpsc_product_category=boat-propeller

Also check this.

http://www.rcdhamaka.com/index.php?main_page=product_info&cPath=56&products_id=639&zenid=sgrq01uh2tfbm8ra5lq3iehl44

@Nik i need ur help in building a robot

Nice one nick 

I have built a similar  boat Catamaran style will post soon .

great build, very good paint job also.

Thank you suk , and desachristopher