RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: March 10, 2023, 12:19:49 AM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023




I am making a quadcopter using 30 amp esc and 2200kv bldc motors with apm 2.8 flight controllers. Sometime before all of my escs stated constantly beeping when connected to the flight controller and powered on but when I try to remove them from flight controller and do the calibration plugging the esc to 3rd channel and starting in throttle up and after 3..4 beeps lowering down the throttle and then the motor works perfectly even in this process there is not continuous beep but When I attach the same calibrated motor to apm 2.8 it again starts beeping even everything is fine in flightcontroller and it is perfectly calibrated too?? Please help me
Logged
 

Read
« Reply #1 on: March 10, 2023, 12:22:24 AM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



Moreover, I have tried starting it in throttle down pos and even checking the supplies its completely fine the esc is simonk red
Logged
 

Read
« Reply #2 on: March 10, 2023, 08:56:47 AM »
Pradeeppk
Plane Lover
Active Member
**

Reputation Power: 1 
Pradeeppk has no influence.
Offline Offline

City: Dibai
State: Uttar Pradesh
RC Skills: Advanced
Posts: 41
Join Date: Jan, 2022



Which transmitter you have used
Logged
 

Read
« Reply #3 on: March 10, 2023, 11:01:17 AM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



The transmitter used is fs-ct6b 6channel 2.4 ghz one again it is also bindes properly to receiver as when I directly plug in motors without apm everything works fine
Logged
 

Read
« Reply #4 on: March 10, 2023, 11:16:51 AM »
Pradeeppk
Plane Lover
Active Member
**

Reputation Power: 1 
Pradeeppk has no influence.
Offline Offline

City: Dibai
State: Uttar Pradesh
RC Skills: Advanced
Posts: 41
Join Date: Jan, 2022



Ok in my case i fixed this issue using transmitter
In transmitter setup go to End points and decrease the throttle value (channel 3) till the beep stop.
Logged
 

Read
« Reply #5 on: March 10, 2023, 11:19:30 AM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



But I don't have a setup window in my transmitter and I am not able to do it using mission planner could you please tell it how to do
Logged
 

Read
« Reply #6 on: March 10, 2023, 06:01:20 PM »
Pradeeppk
Plane Lover
Active Member
**

Reputation Power: 1 
Pradeeppk has no influence.
Offline Offline

City: Dibai
State: Uttar Pradesh
RC Skills: Advanced
Posts: 41
Join Date: Jan, 2022



Then how you setup your flight controller
Logged
 

Read
« Reply #7 on: March 10, 2023, 06:59:20 PM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



I have set it up using mission planner actually there is no screen on my transmitter and it is working fine when the escs are not connected with the flight controller. the throttle works correctly but when the lead is connected to apm then it starts beeping I will add the pic of my transmitter

Screenshot 2023-03-10 185846.jpg
Re: 30 amp esc onstantly beeping
* Screenshot 2023-03-10 185846.jpg (19.9 KB, 365x357 - viewed 291 times.)
Logged
 

Read
« Reply #8 on: March 10, 2023, 10:22:20 PM »
Pradeeppk
Plane Lover
Active Member
**

Reputation Power: 1 
Pradeeppk has no influence.
Offline Offline

City: Dibai
State: Uttar Pradesh
RC Skills: Advanced
Posts: 41
Join Date: Jan, 2022



Have you done the esc callibration if not please do it may be it solve your problem.There are lots of videos showing how to calibrate esc.
Logged
 

Read
« Reply #9 on: March 10, 2023, 10:43:03 PM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



I have already done all the esc callibration. Thats what I am trying to tell that whenever I am trying to use direct esc motor and the tx rx it works completely fine and as soon as I plug it to apm the esc start beeping . Escs are calibrated correctly
Logged
 

Read
« Reply #10 on: March 10, 2023, 11:43:40 PM »
Pradeeppk
Plane Lover
Active Member
**

Reputation Power: 1 
Pradeeppk has no influence.
Offline Offline

City: Dibai
State: Uttar Pradesh
RC Skills: Advanced
Posts: 41
Join Date: Jan, 2022



Ok bro in my way u need to decrease the end points value.
And hope someone better helps you best regards 👍
Logged
 

Read
« Reply #11 on: March 11, 2023, 12:25:53 AM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



Yep I have tried that I need help if anyone here notices
Logged
 

Read
« Reply #12 on: March 11, 2023, 10:56:32 AM »
K K Iyer
Global Moderator
Forum Hero
*****

Reputation Power: 61 
K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!
Offline Offline

City: Indore
State: Madhya Pradesh
RC Skills: Intermediate
Posts: 5165
Join Date: Jan, 2012



Moreover, I have tried starting it in throttle down pos and even checking the supplies its completely fine the esc is simonk red

Try with throttle trim at minimum with throttle stick at idle.
Logged
 

Read
« Reply #13 on: March 11, 2023, 11:02:40 AM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



I have tried this too but the beep is constant like every second whenever Connected to apm but direct connection of the same ecs and motor to tx rx and lipo battery works fine
Logged
 

Read
« Reply #14 on: March 11, 2023, 11:39:13 PM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



Please sort this out sir as this is my final year project
Logged
 

Read
« Reply #15 on: March 20, 2023, 07:12:51 PM »
Hellyflyer
Heli Lover
Forum Hero

*****

Reputation Power: 20 
Hellyflyer barely matters.Hellyflyer barely matters.
Offline Offline

City: New Delhi
State: Delhi
RC Skills: Advanced
Posts: 1510
Join Date: Oct, 2009

Heli=Diff parts flying together in close formation



Have you tried reversing the throttle, I don't have much of Apm experience, but generally this constant beeping means that the throttle is not set to its lowest position and as soon as you connect the battery the esc detects power and as a failsafe feature it starts beeping.

Share a video of whats happening, may be that clears the air. Thanks
Logged

Helis and Quads ROCK !!
 

Read
« Reply #16 on: April 08, 2023, 05:05:01 PM »
Hangsai
Plane Lover
Active Member
**

Reputation Power: 1 
Hangsai has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Intermediate
Posts: 10
Join Date: Mar, 2023



https://drive.google.com/file/d/1t4Z_9oDoDjpTb4icoe1wmRaOYdiW6Vkv/view?usp=sharing
here is the link of the video I have tried everything please help!!!!!
Logged
 

Read
« Reply #17 on: July 15, 2023, 09:48:54 AM »
Hellyflyer
Heli Lover
Forum Hero

*****

Reputation Power: 20 
Hellyflyer barely matters.Hellyflyer barely matters.
Offline Offline

City: New Delhi
State: Delhi
RC Skills: Advanced
Posts: 1510
Join Date: Oct, 2009

Heli=Diff parts flying together in close formation



https://drive.google.com/file/d/1t4Z_9oDoDjpTb4icoe1wmRaOYdiW6Vkv/view?usp=sharing
here is the link of the video I have tried everything please help!!!!!

Center all trims and try again, also make sure all switches are at 0 position
Logged

Helis and Quads ROCK !!
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
PLZ HELP SOON.......... MOTOR BEEPING AND DID NOT START.
Electric Power
manojswizera 20 16569 Last post October 29, 2011, 09:05:52 PM
by Sumeet
unnecessary beeping of motors in quadcopter.
Multirotors
prateek katiyar 1 2304 Last post January 09, 2014, 06:57:06 PM
by SideWinder
ESC beeping continuously « 1 2  All »
Electric Power
phanivyas 30 23453 Last post November 25, 2014, 11:07:48 PM
by stadsocare
FS-IA6 Receiver Beeping???!!
Beginners Zone
tiluji 8 3664 Last post January 31, 2017, 11:31:47 PM
by swapnilnimbalkar
[SOLVED] A2212 motor keeps beeping, does not run. Help.
Electric Power
ariyano 8 17050 Last post September 20, 2018, 05:46:36 AM
by ariyano