greetings folks,
am skykalai. i have a FSi6S transmitter. I know all the modes in the transmitter, but still i don't know stick adjust setup . any one can help me to know more about stick adjust. i got some problem in stick adjust , when i entered to the stick adjust side, i won't go back again.  so i want turn off the tx and turn on again. then only it shows me a main screen. but i know onething, it completely depends on throttle.
so reple me friends

you save settings by holding cancel button if you are asking how to save settings.

yeah but, my tx is FSi6S, not i6 or i6X. there is no cancel button, and also if i want to change that by using refresh, it wont work.. i dont know why this happening...
and thanks for reply 

”If you cannot go back, it means that...”

Quoted from step 2 of item 7.5 of the FSI6S manual
https://www.flyingtech.co.uk/sites/default/files/product_files/FS-i6S-MANUAL-EN-20161001.pdf

Hope this helps.
Regards

yeah thanks sir,, now i got to read...and i just send a personal message to you, but you have more unread it wont sent .

this is my message..
hi sir,
i just make a 30" wing span rc plane . all are done but, i extend the wires for the servo motor. so the voltage drop was occurred ( I think) . so the motor is very hard to run. and also, the command takes more time, delay also occurred. so i wish to plan of give  extra power source for a servo. and first of all i doubted, my problem is possible or not?? sir...... so today i do some experiments for giving power supply methods....
1. using dc-dc buck board
 using a 1s battery for the buck board input and adjust the voltage as 5.5 volt for the receiver battery port. the servo works very well. there is only one power supply for the 4 servos and there is no, esc .
2 . using power regulators, but it needs more space . so i rejected it. and also i need to make pcb for the voltage reduction.
 i thinking about use a 3s battery 1s cell to be connected to the buck board, but that one cell voltage reduce quickly, thats why am putting extra 1s battery for buck board...
3. I connect 5v power source to the servo cable. And I connect the signal wire to receiver, the motor esc will power up the receiver. but it wont work.

and finally i happy, and choosing buckboard method. and i connect all he setup for the final test. that means, i connect the esc in 3ch and give a extra power supply in battery port, and connect all the servos.
 and i wish god my setup work well. but it fails, when i turn on the both power supply, the battery port wires are burned . i shocked sir.. hope well, the receiver doesn't get damage. so i thanks god...
why this happening sir ??
and how can i solve this problem??
if you have any idea please tell me sir..
7904349761 this is  my number sir... ( whats app )

and sorry for i didn't mention tx and rx..
im using fsi6x and fsia6b receiver...

thanks sir 

waiting for your reply..

and why my servos didnt work, and product issue, quality, not enough power supply , not enough signal??

Hey post a connection diagram, it will be easier for us.

Also, specifics of your ESC, Servo, Motor, and any other electronics used.

yes sir, and first thanks for reply...
here are the pics..
first i fix the voltage in buck board. and made a connection as per the circuit diagram 2 .
and first put the power supply to the buck board, then turn on the ESC power supply. at the next second the ubec power supply wires burnt. but you can see the receiver picture the ground wire only burnwell, the +vcc wire not burnt. I don't know how this happen sir, i think i made a small mistake in it, but i don't know what it is?. and i saw some ubec videos, those ubec all are having 2 wires only ( +vcc and ground ) . but my circuit why burnt. help me sir..
regards skykalai

I'm using 30A TBS ESC,
 SG90 servo motor(9g, nylon gears),
 , 2200mah 3s lipo for ESC and,
 2200mah 1s lipo(old maybe its mah will reduced) for buck board,
fsi6x tx and fsia6b receiver.
and some DuPont cables(JUmper wires).
regards,
  skykalai