RC India
Welcome Guest, please login or register.
 
Pages: 1 [2] 3 4 5   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« Reply #25 on: July 29, 2018, 07:27:47 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



elevator & rudder

IMG_20180729_192142.jpg
Re: 33 inch blu baby build
* IMG_20180729_192142.jpg (38.09 KB, 605x800 - viewed 427 times.)
Logged
 

Read
« Reply #26 on: July 29, 2018, 08:14:59 PM »
K K Iyer
Global Moderator
Forum Hero
*****

Reputation Power: 61 
K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!
Offline Offline

City: Indore
State: Madhya Pradesh
RC Skills: Intermediate
Posts: 5165
Join Date: Jan, 2012



@taksh
For pushrods for foamies, phool jhaadu ki teeli is the lightest option.
See my earlier post.
I never needed cycle spokes or umbrella wires for push rods.

For connecting to horns, use wire from paper clips. Tied on with dhaaga, sealed with a drop of CA
Logged
 

Read
« Reply #27 on: July 30, 2018, 08:40:32 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



@K K Iyer Sir
Today i tried umbrella rods but later used a few drops of CA and then it stuck. Now i am going to try bamboo and wire from paper clips.
 
« Last Edit: July 30, 2018, 09:56:22 PM by taksh » Logged
 

Read
« Reply #28 on: August 01, 2018, 09:01:33 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



Rudder & elevator Done.
@K K Iyer sir Thanks. Your method works. I used bamboo and paper clips but wire(from paperclip) gets bend at maximum throw and again come back in its position but this happen only at rudder side.

Now my question is maximum throw of both rudder and elevator and how to measure maximum throw as angle. i mean right method to measure.
Logged
 

Read
« Reply #29 on: August 01, 2018, 09:36:22 PM »
K K Iyer
Global Moderator
Forum Hero
*****

Reputation Power: 61 
K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!
Offline Offline

City: Indore
State: Madhya Pradesh
RC Skills: Intermediate
Posts: 5165
Join Date: Jan, 2012



Rudder & elevator Done.
@K K Iyer sir Thanks. Your method works. I used bamboo and paper clips but

1. wire(from paperclip) gets bend at maximum throw and again come back in its position but this happen only at rudder side.

2. Now my question is maximum throw of both rudder and elevator and how to measure maximum throw as angle. i mean right method to measure.

1. It means that the servo is pulling/pushing the rudder more than it can move.
a. If your tx has TVA, reduce it to about 80% on rudder channel
b. If your tx has EPA (end point adjustment), reduce it to about 80% on both sides of rudder channel
c. If your tx has dual rates, select about 80% on high rate
c. If you have none, move the pushrod one hole closer to center on the servo arm, or one hole farther from the base on the rudder control horn

2. Use a protractor (also known as a D) from a geometry box!
Logged
 

Read
« Reply #30 on: August 01, 2018, 09:49:21 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



 Head Scratching
I think video is better.
I will upload video.

I have 9x. I don't know tva,epa  dual rates. I will search on google.
Logged
 

Read
« Reply #31 on: August 02, 2018, 10:48:05 AM »
rastsaurabh
Plane Lover
Forum Hero

*****

Reputation Power: 19 
rastsaurabh has no influence.
Offline Offline

City: Noida
State: Haryana
RC Skills: Intermediate
Posts: 1558
Join Date: Mar, 2012



TAKSH,

Your TX has end point settings. I would suggest you download the TX manual and read about it.

In your first model you dont need to put Expo , dual rates etc. just adjust the end points so that overthrows are not there.

Keep reading of all those stuff and do trial on non flying model.... and implement it on flying model as you become expert in flying.

Frankly while first time flying you would struggle to change the switch for dual rates.
Logged
 

Read
« Reply #32 on: August 03, 2018, 02:00:47 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



barbecue skewers kaha milenge? wings ka fitting ka liya chahiye.
Logged
 

Read
« Reply #33 on: August 03, 2018, 05:10:56 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



How to balance cg? there is two marking 2.6 inch and 2.3 inch.
So, plane cg should have to be balanced between 2.6 and 2.3 inch?
i mean cg 2.6 or 2.3 inch ka bich honi chahiye ?
Logged
 

Read
« Reply #34 on: August 03, 2018, 05:18:31 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



Confusion hai baas thodi si.
Logged
 

Read
« Reply #35 on: August 03, 2018, 05:19:39 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



Confusion hai baas thodi si.
Logged
 

Read
« Reply #36 on: August 03, 2018, 06:42:23 PM »
tictoc21
Heli Lover
Forum Veteran

****

Reputation Power: 6 
tictoc21 has no influence.
Offline Offline

City: mumbai
State: Maharashtra
RC Skills: Intermediate
Posts: 439
Join Date: Jun, 2015



To find cg
Remove all electronics, motor battery ecs Rx servo
Just have model
Of course at this stage model is surely tail heavy now add some coins by taping it with transparent plastic tape.
Then throw your craft at ground level about from 1m from ground
If it is again tail heavy add some coins again, do this several time till the aircraft become level when you throw in air 1m from ground surface.
When you see if it is flying level then stop adding coins.
When craft lands on surface lift it at such point such that it becomes level.
Move 1 inch forward from that point and mark this point as cg.
Now add your electronics, and balance a very little nose heavy by battery adjustment.
And take out for flying.
This is what I'm doing from several years, and all models are flying great, no craches till now due cg point.
Hope you understand.
Have a nice flight.
Logged
 

Read
« Reply #37 on: August 03, 2018, 06:49:46 PM »
Mehul Anand
Plane Lover
Senior Member
***

Reputation Power: 4 
Mehul Anand has no influence.
Offline Offline

City: Ranchi
State: Jharkhand
RC Skills: Beginner
Posts: 217
Join Date: Feb, 2018



Sir,
Why 1 inch ahead  the CG should be??
And towards the nose or tail??
Logged
 

Read
« Reply #38 on: August 03, 2018, 06:51:02 PM »
tictoc21
Heli Lover
Forum Veteran

****

Reputation Power: 6 
tictoc21 has no influence.
Offline Offline

City: mumbai
State: Maharashtra
RC Skills: Intermediate
Posts: 439
Join Date: Jun, 2015



Remember nose heavy plane are not good to fly and tail heavy are unable to fly...
Logged
 

Read
« Reply #39 on: August 03, 2018, 06:57:26 PM »
K K Iyer
Global Moderator
Forum Hero
*****

Reputation Power: 61 
K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!
Offline Offline

City: Indore
State: Madhya Pradesh
RC Skills: Intermediate
Posts: 5165
Join Date: Jan, 2012



@taksh,
It will be ok if it balances about 2.5” behind the leading edge.
This is within the range mentioned on the plan (2.3-2.6”)
Logged
 

Read
« Reply #40 on: August 03, 2018, 07:03:26 PM »
tictoc21
Heli Lover
Forum Veteran

****

Reputation Power: 6 
tictoc21 has no influence.
Offline Offline

City: mumbai
State: Maharashtra
RC Skills: Intermediate
Posts: 439
Join Date: Jun, 2015



Sir,
Why 1 inch ahead  the CG should be??
And towards the nose or tail??
The 1 inch is to balance any wrong measurement in cg.
And it should be towards nose.
Bcoz if you make if toward tail the plane may be nose heavy and when you add battery to balance it, you will have move battery back and the aircraft may get tail heavy.
So counteract this the cg point is taken 1 inch toward nose so that when you balance it by battery the will have to move forward which will make plane nose heavy.
Nose heavy are better than tail heavy to avoid crash.
Hence when you move it forward 1 inch then for next flight the plane will be available to move battery to back.
If 1 inch is taken toward the plane may get crash and ofcource it will be not available to adjust the battery.
Logged
 

Read
« Reply #41 on: August 03, 2018, 07:34:18 PM »
K K Iyer
Global Moderator
Forum Hero
*****

Reputation Power: 61 
K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!
Offline Offline

City: Indore
State: Madhya Pradesh
RC Skills: Intermediate
Posts: 5165
Join Date: Jan, 2012



There are two simple methods in use for the last 100 years or so.
1. Balance the model within the range shown on the plans (available in this case)
2. If the plan does not indicate, balance between 25-33% of the chord from the leading edge.

Hope this helps. And does not confuse.
Logged
 

Read
« Reply #42 on: August 03, 2018, 10:55:13 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



@tictoc21 @K K Iyer
Thanks
Logged
 

Read
« Reply #43 on: August 09, 2018, 02:44:37 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



I have used A2212 1000kv motor and 1045 propeller and I tested plane in my home.
Rudder is not at center So, i used subtrim functions of tx so rudder can be in center.
I just increased throttle slowy and many times i increased throttle to 50% fastly then i decreased throttle to 0%.
but problem is coming. Plane is automatically turned to left side.
Rudder problem? or troque roll problem i mean i need to set thrust angle?
what's problem with my plane?
Note: I have installed landing gear to my rc plane then i tested. Landing gear is fixed with zipties and glue gun and CA.
Plane's cg is not balanced. Tail is heavy. I just tested plane. I just  want plane to move forward but plane moved but plane also moved left side.
Motor rotation & propeller : Counter clock wise.

Logged
 

Read
« Reply #44 on: August 09, 2018, 03:27:10 PM »
prabal276
In the Air
Plane Lover
Forum Hero

*****

Reputation Power: 15 
prabal276 has no influence.
Offline Offline

City: Delhi
State: Delhi
RC Skills: Intermediate
Posts: 1417
Join Date: Mar, 2013

One step at a time :)



the landing gear may not be straight.
In my Old Fogey , the landing gear caused the same problem......
Logged
 

Read
« Reply #45 on: August 09, 2018, 06:07:58 PM »
K K Iyer
Global Moderator
Forum Hero
*****

Reputation Power: 61 
K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!
Offline Offline

City: Indore
State: Madhya Pradesh
RC Skills: Intermediate
Posts: 5165
Join Date: Jan, 2012



Push the model by hand, without running motor.
See if it rolls straight.
If not, wheels are not aligned, or more friction in one wheel.
Logged
 

Read
« Reply #46 on: August 10, 2018, 10:05:36 AM »
rastsaurabh
Plane Lover
Forum Hero

*****

Reputation Power: 19 
rastsaurabh has no influence.
Offline Offline

City: Noida
State: Haryana
RC Skills: Intermediate
Posts: 1558
Join Date: Mar, 2012



Taksh ......

Paste the pic of the model........
Logged
 

Read
« Reply #47 on: August 10, 2018, 10:15:48 AM »
girishsarwal
Plane Lover
Forum Hero

*****

Reputation Power: 17 
girishsarwal has no influence.
Offline Offline

City: Gurgaon
State: Haryana
RC Skills: Beginner
Posts: 1420
Join Date: May, 2012

DIYer



In order you might want to
- affix the LG property with screws or glue or insert in slot, not with zip ties.
- the LG is not properly perpendicular to fuse
- the left wheel is stuck, while the right is moving, both of them are not moving at the same speed
- if it's going a little to the left and can be steered using the rudder, use rudder on takeoff
Logged

gs
 

Read
« Reply #48 on: August 10, 2018, 02:23:06 PM »
prabal276
In the Air
Plane Lover
Forum Hero

*****

Reputation Power: 15 
prabal276 has no influence.
Offline Offline

City: Delhi
State: Delhi
RC Skills: Intermediate
Posts: 1417
Join Date: Mar, 2013

One step at a time :)



Also, have you given excessive left angle to the motor?
Check for that as well.
Logged
 

Read
« Reply #49 on: August 10, 2018, 04:04:39 PM »
taksh
Plane Lover
Forum Hero
*****

Reputation Power: 10 
taksh has no influence.
Offline Offline

City: GHAZIABAD
State: Uttar Pradesh
RC Skills: Beginner
Posts: 657
Join Date: Nov, 2017



https://i.imgur.com/r8zNk3e.jpg
33 inch blu baby build

https://i.imgur.com/9SJXV43.jpg
33 inch blu baby build

https://i.imgur.com/gcsRjRf.jpg
33 inch blu baby build

https://i.imgur.com/0uyPSK6.jpg[/img[img]https://i.imgur.com/cvicO9u.jpg
33 inch blu baby build

https://i.imgur.com/YacjXeC.jpg
33 inch blu baby build

https://i.imgur.com/o1Dmvze.jpg
33 inch blu baby build

https://i.imgur.com/dktfcSh.jpg
33 inch blu baby build
Logged
 

Pages: 1 [2] 3 4 5   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
Blu-Baby 24 inch aileron version build log « 1 2  All »
Electric Planes
sahilkit 28 30196 Last post April 25, 2011, 05:52:31 PM
by kalvik
Blu Baby 33 inch using Monobloc
Electric Planes
bokilap 21 16572 Last post May 07, 2011, 06:54:27 PM
by bokilap
Scratch Build (log) - Blu Baby 33"
Electric Planes
Aafi 14 12763 Last post October 05, 2011, 03:20:59 AM
by ujjwaana
Blue Baby 33 Inch
Electric Planes
Mjet 7 4973 Last post September 03, 2012, 08:43:57 PM
by Mjet
[BUILD] Baby Blender V2
Electric Planes
aniket210696 13 9885 Last post September 15, 2014, 09:50:16 AM
by niteenk