RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: April 04, 2014, 10:15:52 AM »
iwincar
Plane Lover
Senior Member
***

Reputation Power: 3 
iwincar has no influence.
Offline Offline

City: Mumbai
State: Maharashtra
RC Skills: Beginner
Posts: 245
Join Date: Jul, 2013




do you think following set up should be good enough to start 40" coro build

(Tx rx not available )

From rc Bharat
   
ZOP Power 2200Mah Lipo--       Rs 1,189   
Specification
Battery Configuration: 11.1V 2200mAh 3cell
Battery Capacity: 2200mAh
Max Continuous Discharge (C-rate/current): 20C
Max Burst (3Sec) (C-rate/current): 45C
Approx Dimensions H x W x L (mm): 22.0 x 35 x 104
Approx Weight (g): 166.5
Max Charging rate: 2C

   
Mystery Pentium 30A Brushless ESC--       Rs 957   
Weight: 28g /0.99 oz
Size: 45X24X9mm
Features:
Constant current 30A Max 40A <10s
Li-Poly 2-3 cells;
Ni-MH 4-10 cells Auto Detect Break On/Off; Progarmmable
BEC: 2A
Auto Low battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell Lipo


Mystery A2212-6 2200KV Brushless Outrunner Motor--       Rs 897   
RPM/V      2200KV
No. Of cells        5-7Ni-MH/2-3Li-Po
Max. efficiency current      14 - 22 A (>72%)
NoLoad current / 10 V        1.4 A
Current capacity        28 A/ 60 s
Max. efficiency          0.75
Shaft diameter (mm) 3 mm
Weight with cables    47 g
Internal Resistance     45 mΩ
Dimensions(mm)       27.5x30
Recomended model weight :300-1000g
Recomended prop without gearbox   2xLi 7"x5",3xLi 5"x5",3xLi - heli
Remarks:   Ideal to work with our 20A ESC and 30A ESC For A2212/6 and A2212/10


Mystery 9grm Analog Metal Gear Servo--       Rs 491   

Size mm 22.8*12.2*28.5
Weight g 13.4g
Stall torque 1.8kg/cm(4.8v) 2.2kg/cm(6.0v)
Operating speed 0.10sec/60degree(4.8v) 0.08sec/60degree(6.0v)
Operating voltage 4.8V
Dead band width 5μs

ES9051 (4.3G) DIGITAL SERVO.      350/-        Kinetic hobby


Direct Drive Prop 8x6--       Rs 48   or

Electric Prop 9x6--       Rs 80   or

9x5 1CW & 1CCW--       Rs 147   or

Slow Fly Propeller 9x4.7 Pair--       Rs 185 ( suggest best)

Control Horns 16x20mm (6pcs)--      @ Rs 10   Rs 58

From rcdhamaka
Charger
V3+ AC240v 2/3s Lipo/Life Charger.        649/-

Still not getting wires and carbon rods.
Logged
 

Read
« Reply #1 on: April 04, 2014, 11:17:03 AM »
manojswizera
Plane Lover
Forum Hero

*****

Reputation Power: 18 
manojswizera has no influence.
Offline Offline

City: AURANGABAD
State: Maharashtra
RC Skills: Beginner
Posts: 1336
Join Date: Oct, 2011



According to the what i have seen and discussed with my friend,  Zop lipo are not as good. (my personal opinion)
Go with 1000-1200 kv motors with 9-10' props, according to the motor.
don't even think of 8-9 inch prop on 2200 kv motor, you will end up burning it. These high kv motors need 5-6 inch prop, and are usually used in pusher setup.
 9 grams servos work well, for coro model of 40 span, no need for expensive metal gear servos.( if you have good budget, you can go for metal gear servos, they last long )

For control rods, you can use cycle spokes.
Logged

Russ-40 Trainer, Mr.moss, Pushler, Skysurfer, Mugi , F-22, Red swan, Xtra-300, redfury, flying mantaray.
 

Read
« Reply #2 on: April 04, 2014, 11:50:42 AM »
Swapnil
Plane Lover
Forum Hero

*****

Reputation Power: 20 
Swapnil barely matters.Swapnil barely matters.
Offline Offline

City: Pune
State: Maharashtra
RC Skills: Beginner
Posts: 1755
Join Date: May, 2010

Retreat, Hell!



For control rods you can also use gel-refills or better ice-cream sticks-halved-longitudinally and joint end-to-end.

1000 kv (200W to 240W) with a 10x4.5 or 10x5 prop and a 1200mAH to 1500maH 3S LiPo is a really good setup. Metal gear servos cost a bit more but won't give you headaches. 
Logged
 

Read
« Reply #3 on: April 04, 2014, 03:08:22 PM »
iwincar
Plane Lover
Senior Member
***

Reputation Power: 3 
iwincar has no influence.
Offline Offline

City: Mumbai
State: Maharashtra
RC Skills: Beginner
Posts: 245
Join Date: Jul, 2013



@Swapnil @Manoj thanks
I am not planning pusher. A normal plane so as per you suggestion

1200 Kv motor brushless would do.

Qn.
3 ,9gm servo for- rudder,tail,ailerons right?,

For aileron can I use  2 separate  servos ?

Which means 4 channels on Receiver will be occupied for them?

1 Chanel for prop so I would need Rx say 6 Chanel ?

Logged
 

Read
« Reply #4 on: April 04, 2014, 03:59:57 PM »
manojswizera
Plane Lover
Forum Hero

*****

Reputation Power: 18 
manojswizera has no influence.
Offline Offline

City: AURANGABAD
State: Maharashtra
RC Skills: Beginner
Posts: 1336
Join Date: Oct, 2011



You can use 1 servo or 2 separate servos for aileron. But only one channel will be occupied , as both servos will be connected by a Y connector.
Actually 4 channel radio will do the work. But i suggest you go with 6 Channels. because will will need to upgrade soon. Better if you go for a programmable radio, with screen.
Logged

Russ-40 Trainer, Mr.moss, Pushler, Skysurfer, Mugi , F-22, Red swan, Xtra-300, redfury, flying mantaray.
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
Wanted used electic parts for blu baby 33
Wanted
rcpilot 4 2074 Last post September 26, 2012, 02:22:11 PM
by amansachdeva22
i urgently want an electic speed controller,please! and i want it a bit cheap
Wanted
rejith 3 1700 Last post April 18, 2013, 08:47:12 PM
by arun.sreelakam
TREX 500 Clone + Electronic
For Sale - Completed
Shannon 1 2079 Last post May 10, 2013, 07:47:29 PM
by Priyum
sky surfer with electronic wanted.......
Wanted
jayantpradhan 10 3328 Last post December 24, 2014, 06:24:28 AM
by rcsportz
Electronic component ...?
Servos, Gyros and All Electronics
mahir.asrani 21 19721 Last post June 29, 2014, 07:18:32 AM
by alokhovercraft