Title: RE-Birth of AXN Floater....NEED HELP !!! Post by: madaquif on January 03, 2014, 07:49:41 PM 2013 was amazing for a starch building.... >:D
Built n flew FT Nutball and FT Flyer with the help of senior members.... :bow: But as per a senior flyer suggestion....I needed a trainer model to learn to fly .... I need to learn as soon as I can so instead of building a model, I decided to buy one and learn to fly (:|~ So after doing some research ....I decided to go for a AXN floater. One of my friend from Chennai had a AXN Floater Air Frame (slightly damaged and wing tip cut).(attached the pics).. I will be enforcing the model in the best possible way I can think of, using 1/2/3 mm CF rods n tubes. Pic 1 > wing parts pic 2 > damaged fuse....hot water treatment should fix it pic 3 > fuse with the canopy pic 4 > motor mount. I have already have the following electronics > Turnigy 9x tx/rx > 4X 9 gm servos > 30 amps OEM ESC >6/4 props Now I'm confused with which motor I should be using for this model as the weight will be increased :headscratch: :headscratch: :headscratch: Senior members please suggest a good motor for my model along with the source to buy if possible. :help: :help: :help: Awaiting help and suggestions :bow: Title: Re: RE BIRTH OF AXN FLOATER....Need help !!! Post by: rcrcnitesh on January 03, 2014, 08:01:12 PM Although I am not an expert but if the plane can handle a 6x4 these motors would be good.
http://hobbyking.com/hobbyking/store/__21482__NTM_Prop_Drive_28_36_2700KV_595W.html (http://hobbyking.com/hobbyking/store/__21482__NTM_Prop_Drive_28_36_2700KV_595W.html) http://hobbyking.com/hobbyking/store/__21481__NTM_Prop_Drive_28_36_2200KV_696W.html (http://hobbyking.com/hobbyking/store/__21481__NTM_Prop_Drive_28_36_2200KV_696W.html) from India http://aeroworks.co.in/store/index.php?id_product=42&controller=product (http://aeroworks.co.in/store/index.php?id_product=42&controller=product) Title: Re: RE BIRTH OF AXN FLOATER....Need help !!! Post by: aniket210696 on January 03, 2014, 08:01:39 PM get a axn floater motor 2150 kv. it can run on a 20a-30a esc
or get a turnigy 22826 2200kv motor. this ill give you enough thrust, but you may require a 40a esc. Title: Re: RE BIRTH OF AXN FLOATER....Need help !!! Post by: madaquif on January 03, 2014, 08:30:25 PM Thanks for your suggestions nitesh and aniket,
however the motor mount on the plane is for 22 size motors....will 28 size motor fit in ? @nitesh...I have 30 amps esc...so NTM 28-36 would probably burn my ESC Title: Re: RE-Birth of AXN Floater....NEED HELP !!! Post by: rcrcnitesh on January 04, 2014, 12:52:20 PM you are right.
use this motor http://rchobbyaddict.com/product_info.php?cPath=53_90&products_id=424 (http://rchobbyaddict.com/product_info.php?cPath=53_90&products_id=424) Title: Re: RE-Birth of AXN Floater....NEED HELP !!! Post by: madaquif on January 15, 2014, 02:24:37 AM Today i started the re-building of AXN Floater..... ;D
joined the wing tips on both the wings using bondtite clear. please note in pic 3 the wing tip joint has a little inward bump (marked in red)....will that change any major flight characteristics???? Title: Re: RE-Birth of AXN Floater....NEED HELP !!! Post by: madaquif on January 17, 2014, 08:03:26 AM in the 3rd pic above.... the wing tip joint has a little inward bump (marked in red)....will that change any major flight characteristics????
Title: Re: RE-Birth of AXN Floater....NEED HELP !!! Post by: allthatido on January 17, 2014, 12:07:20 PM Nope..just put a tape over it
Title: Re: RE-Birth of AXN Floater....NEED HELP !!! Post by: sundaram on January 17, 2014, 12:34:42 PM All the motor sugesstions above are too powerful and heavy for this model.
You need only a 2805 2200 KV equivalent motor with 4.5x4.5 prop on 3S or 6x3 on 2S and 18-20 Amps ESC for this model. http://www.rcdhamaka.com/index.php?main_page=product_info&cPath=100_93&products_id=760 (http://www.rcdhamaka.com/index.php?main_page=product_info&cPath=100_93&products_id=760) Title: Re: RE-Birth of AXN Floater....NEED HELP !!! Post by: sbajare on January 17, 2014, 01:36:09 PM hi,
i have the perfect motor for it. regds ;) Title: Re: RE-Birth of AXN Floater....NEED HELP !!! Post by: ashimda on January 17, 2014, 02:01:45 PM hi, What motor is that if you don't mind me asking.i have the perfect motor for it. regds ;) |