Title: scratch built corro trainer by v2_eagle Post by: kunal mathur on July 21, 2016, 08:35:21 PM Hi after a little success with my brother's flying wing. I decided to do my first build . So Here is a high wing trainer copied from v2 eagle . Initially I made it according to the plans but later I realised that the dihedral wings get folded in air . So I am made it a flat wing . It's yet to be flown . Now my brother has built some wonderful landing gear. To TAKE OFF rather than chuck launch. Thanks Bro.
Will post pics and data Title: Re: Post by: v2 eagle on July 22, 2016, 04:20:02 PM At first I thought it was my name. BTW can you post pics of actual plane.
Sent from my ZUK Z1 using Tapatalk Title: Re: scratch built corro trainer by v2_eagle Post by: sanjayrai55 on July 22, 2016, 06:01:42 PM At first I thought it was my name. :giggle: :giggle: :giggle: Title: Re: scratch built corro trainer by v2_eagle Post by: sanjayrai55 on July 22, 2016, 06:07:16 PM Kunal
A dihedral has a very important function, especially in trainers It has a stabilising effect. The wing if banked, will automatically tend to level out when you leave the controls It enhances rudder effect greatly To prevent the wing folding, strengthen the centre: Doubler on the spar centre (http://s25.postimg.org/4j1hfyyin/IMG_20160527_063044.jpg) Corro Wing wrap on the wing centre (http://s25.postimg.org/r90m8yhq7/IMG_20160529_125030.jpg) Title: Re: scratch built corro trainer by v2_eagle Post by: SI74 on July 22, 2016, 07:12:25 PM At first I thought it was my name. 😄 :) I too thought it was you! :) Title: Re: scratch built corro trainer by v2_eagle Post by: kunal mathur on July 23, 2016, 08:02:32 PM Yes @v2 eagle Sir it was you, I copied your plan.
Regards Title: Re: scratch built corro trainer by v2_eagle Post by: kunal mathur on July 23, 2016, 08:07:40 PM Thanks Sanjay Sir, actually at that time I was unable to find the best way to strengthen the wing and prevent it from folding with dihedral too
So finally make that wing to a straight wing And yes Sir I know I have lost the advantages of a dihedral wings , mainly Stability but will build another soon And do maiden with this straight wing when my tx and rx module will delivered. Regards Title: Re: scratch built corro trainer by v2_eagle Post by: kunal mathur on July 23, 2016, 08:11:08 PM @ Sanjay Sir I didn't understand above said and in the pic I see spars on the mid of the wing then now it will retain dihedral
Forgive if any silly question asked Regards Title: Re: scratch built corro trainer by v2_eagle Post by: sanjayrai55 on July 24, 2016, 06:38:20 AM Kunal:
1. The dihedral in a corro wing is basically set from the spar. Take the two spar halves, and set to the desired dihedral angle. Then, reinforce the centre joint by gluing another piece of wood (or more, according to the size) in the centre. Sand to fit neatly. For smaller models corro spars are also used; typically doubled up corro with the flutes running perpendicular to each other. The centre reinforcing doubler is done the same way 2. On the assembled wing, a centre wrap of corro is glued. The width will be the fuselage width plus some more. Corro used will be same thickness as wing. By doing these two techniques, the chances of a wing folding are minimal. In fact, I have NEVER had a corro wing fold! (Altough I have had two - both the foamies I made - foam wings fold :D :D ) Title: Re: scratch built corro trainer by v2_eagle Post by: kunal mathur on July 24, 2016, 08:30:18 AM Thanks Sir
And sir after my desired dihedral will glue 2 half spars and for centre spar can I use very shaped spar Thanks again Regards Title: Re: scratch built corro trainer by v2_eagle Post by: kunal mathur on February 26, 2017, 10:26:27 AM Maiden video
https://m.facebook.com/story.php?story_fbid=893003627471997&id=100002871036422 Title: Re: scratch built corro trainer by v2_eagle Post by: sanjayrai55 on February 26, 2017, 10:49:17 AM Very courageous: to take off on a narrow road with buildings and electric cables lining it >:D >:D {:)}
Title: Re: scratch built corro trainer by v2_eagle Post by: swapnilnimbalkar on February 26, 2017, 11:56:05 AM I'm unable to see the video.
Title: Re: scratch built corro trainer by v2_eagle Post by: kunal mathur on February 26, 2017, 12:02:24 PM Why?
Are you not on Facebook Title: Re: scratch built corro trainer by v2_eagle Post by: samayaraj on February 27, 2017, 03:51:15 PM Hi after a little success with my brother's flying wing. I decided to do my first build . So Here is a high wing trainer copied from v2 eagle . Initially I made it according to the plans but later I realised that the dihedral wings get folded in air . So I am made it a flat wing . It's yet to be flown . Now my brother has built some wonderful landing gear. To TAKE OFF rather than chuck launch. Thanks Bro. Will post pics and data You can try ply wood strips instead of balsa spar. It will give you enough strength. Title: Re: scratch built corro trainer by v2_eagle Post by: kunal mathur on February 28, 2017, 02:09:59 PM Sure @samayaraj
Regards Title: Re: scratch built corro trainer by v2_eagle Post by: stadsocare on April 29, 2017, 10:34:23 AM AS per Our Responsibility for care while flying, one has to see that there are no hazardous or life threatening,or like high tension electric wires around while flying, if there is any accident, it will probably block us or will suffer permissions to fly, we must respect our flying conditions and rules and ensure that we do not hurt anyone. Our Authorities will surely help us
|