Title: Scratch built Pusher - Build log Post by: docnayeem on May 29, 2014, 05:56:03 PM A similar aircraft
Build material HD EPS foam Bio- foam Pine Sticks Title: Re: Scratch built Pusher - Build log Post by: sanjayrai55 on May 29, 2014, 05:59:06 PM Good luck Doc :D
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 29, 2014, 06:09:00 PM HD EPS foam
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 29, 2014, 06:10:37 PM Getting the Profile
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 29, 2014, 06:11:42 PM Reenforcement with Pine sticks
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 29, 2014, 06:13:43 PM Sandwiched in other foam block to get the bulk of fuselage ....
Its going to be a sea plane lile mermaid so needs a large surface area Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 29, 2014, 06:14:37 PM Getting into shape
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 29, 2014, 06:15:40 PM Thanks a lot Sanjay sir ...
Comments and suggestions ... Are welcome Title: Re: Post by: docnayeem on May 29, 2014, 06:37:56 PM Planning for a wing span of 30 in and mean cord of 6 in ... So got to limit the weight to aroung 500 gms for good flying characteristics ... Going to be a rope walk
Title: Re: Scratch built Pusher - Build log Post by: sanjayrai55 on May 29, 2014, 07:13:02 PM I think you'll have to go lighter at that size
Title: Re: Post by: docnayeem on May 29, 2014, 07:24:01 PM You mean below 500 gms ?
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 30, 2014, 11:16:33 PM Tail assembly and cavities for battery and receiver carved
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 30, 2014, 11:17:33 PM Tail assembly in place
Title: Re: Post by: docnayeem on May 31, 2014, 10:25:55 AM Weight 120gms so far ...
Title: Re: Re: Scratch built Pusher - Build log Post by: sanjayrai55 on May 31, 2014, 01:40:08 PM Nice :D
Title: Re: Post by: docnayeem on May 31, 2014, 02:31:38 PM Planning for a KFm 1 or 2 aerofoil as per weight consideration
Title: Re: Post by: docnayeem on May 31, 2014, 02:31:56 PM Thanks Sanjay sir
Title: Re: Scratch built Pusher - Build log Post by: topalle on May 31, 2014, 03:20:22 PM Seaplane? Wow!
Have you tested it on water? Title: Re: Scratch built Pusher - Build log Post by: rcrcnitesh on May 31, 2014, 03:35:50 PM keep it on very good looking till now
Title: Re: Post by: docnayeem on May 31, 2014, 04:38:54 PM Thanks nitesh .... Hope it will get better :)
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 31, 2014, 05:41:00 PM KMf 2 aerofoil with 8 mm biofoam and pine stick as reinforcement glued and fastened with masking tape
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on May 31, 2014, 05:42:59 PM Assembled just to have a preview ... ;)
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on June 01, 2014, 10:05:04 AM Wing in place and the motor mount made in Foam board
Title: Re: Scratch built Pusher - Build log Post by: docnayeem on June 02, 2014, 11:56:12 AM Maiden day today
Title: Re: Scratch built Pusher - Build log Post by: utkarshg13 on June 02, 2014, 05:55:44 PM Very nice sir. How was the maiden?
Title: Re: Scratch built Pusher - Build log Post by: sauank on June 02, 2014, 06:54:04 PM sir
what is the motor,esc,prop configuration of the pusher..???? Title: Re: Post by: docnayeem on June 02, 2014, 08:09:21 PM Maiden was OK ... Was a bit nose heavy ....I have to change the thrust line angle ...
Title: Re: Post by: docnayeem on June 02, 2014, 08:11:48 PM Config : 2000 kV 30 amp 3 cell 2100 prop 6*4
Title: Re: Scratch built Pusher - Build log Post by: ramarao on June 03, 2014, 11:05:03 AM waiting for maiden video...... ;D ;D ;D ;D ;D ;D
Title: Re: Post by: docnayeem on June 03, 2014, 11:34:36 AM Will surely put up after the required modifications
|