RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: April 04, 2015, 08:01:00 PM »
cyberhack
Heli Lover
Forum Hero
*****

Reputation Power: 8 
cyberhack has no influence.
Offline Offline

City: MUMBAI
State: Maharashtra
RC Skills: Beginner
Posts: 637
Join Date: Aug, 2014




hello guys..
need help am building a 250 racer quad and have 2300kv dys motors and 30amps esc for them a 3s 2200mah lipo 30c and flysky 6ch tx rx well when i connect lipo the esc and check the motor speed after arming and throttling for 10sec the motors heat up and seems about to burn can any one guide me where am i wrng or y is this ?
 are the motors defective or the esc are too much high rated for the motors
Logged
 

Read
« Reply #1 on: April 04, 2015, 08:33:40 PM »
satyagupta
Heli Lover
Forum Hero

*****

Reputation Power: 29 
satyagupta barely matters.satyagupta barely matters.
Offline Offline

City: Navi Mumbai
State: Maharashtra
RC Skills: Beginner
Posts: 2565
Join Date: Mar, 2012



give few more details like
what is the size of the motor?
what propeller size are you using?
What is the ESC you are using?
does the motor heats after spinning? if yes then after how many sec it starts heating
Can you touch the motors? that way we can know how much the heat is.
Logged

 

Read
« Reply #2 on: April 04, 2015, 08:47:14 PM »
cyberhack
Heli Lover
Forum Hero
*****

Reputation Power: 8 
cyberhack has no influence.
Offline Offline

City: MUMBAI
State: Maharashtra
RC Skills: Beginner
Posts: 637
Join Date: Aug, 2014



hello sir,
i am using the below specs:
 ZMR250 Mini Quadcopter Multicopter Frame Kit
------------------------------
esc are xxd escs
Specification:
Power input: 5.6V - 16.8V (2-3 cells Li-Poly, OR 5-12 cells Ni-MH Ni-MH / Ni-Cd battery)
BEC: 2A
Constant current: 30A (Max 40A less than 10 seconds)
---------------------------------
DYS BE1806 2300KV Brushless Motor 2-3S for Mini Multicopters
----------------------------------------------
5030 2-blade Propeller Props 50×3 CW Multicopter/ Quadcopter



---------
open pilot cc3d
-----

well i tried arming and on throttle one of the motor gt hot it was very hot i i could touch 3 of them they were hot bt the 4th one was very hot also at this test i didnt mount props it was without props....
Logged
 

Read
« Reply #3 on: April 05, 2015, 01:09:09 AM »
IndianHobbyShop
Plane Lover
Forum Hero

*****

Reputation Power: 6 
IndianHobbyShop has no influence.
Offline Offline

City: Patna
State: Bihar
RC Skills: Intermediate
Posts: 527
Join Date: Jul, 2013



The props were off while you were doing this test.
Got it.

The question is, How much time did you allowed the motors to run (With props off) before checking it's temperature (by touching it)?
Logged

Regards,
Bhavesh
Indian Hobby Shop
PH# 9473456377
 

Read
« Reply #4 on: April 05, 2015, 01:21:45 AM »
cyberhack
Heli Lover
Forum Hero
*****

Reputation Power: 8 
cyberhack has no influence.
Offline Offline

City: MUMBAI
State: Maharashtra
RC Skills: Beginner
Posts: 637
Join Date: Aug, 2014


Re:

5 to 10 seconds only
Logged
 

Read
« Reply #5 on: April 05, 2015, 01:24:50 AM »
IndianHobbyShop
Plane Lover
Forum Hero

*****

Reputation Power: 6 
IndianHobbyShop has no influence.
Offline Offline

City: Patna
State: Bihar
RC Skills: Intermediate
Posts: 527
Join Date: Jul, 2013



Ok, i could understand one of the motors getting "Too Hot" in 5 seconds
(Due to sorted winding/Faulty Motor)

But i fail to understand the remaining three motors getting 'Hot'.
The temperature raise in those 3 should be almost negligible.

Please confirm.
Logged

Regards,
Bhavesh
Indian Hobby Shop
PH# 9473456377
 

Read
« Reply #6 on: April 05, 2015, 03:46:21 PM »
cyberhack
Heli Lover
Forum Hero
*****

Reputation Power: 8 
cyberhack has no influence.
Offline Offline

City: MUMBAI
State: Maharashtra
RC Skills: Beginner
Posts: 637
Join Date: Aug, 2014



hello sir ,
i did check them idk hope escs is nt the prb and cc3d esc calibration might be wrng wat is the  xxd 30 amp esc setup to be standard esc or turbo pwm in cc3d setup???
Logged
 

Read
« Reply #7 on: April 06, 2015, 05:45:49 AM »
IndianHobbyShop
Plane Lover
Forum Hero

*****

Reputation Power: 6 
IndianHobbyShop has no influence.
Offline Offline

City: Patna
State: Bihar
RC Skills: Intermediate
Posts: 527
Join Date: Jul, 2013



Please use punctuation and don't use SMS Lingos (Forum Rules)
A properly written text helps in easy understanding and will encourage more and more people willing to help.

In order to be double sure, Please swap the problematic motor with any from the remaining 3 and check if the issue persists with that motor.
Most likely you will find the issue repeating with the same motor itself which would mean that the motor is faulty.
Logged

Regards,
Bhavesh
Indian Hobby Shop
PH# 9473456377
 

Read
« Reply #8 on: April 06, 2015, 08:31:32 AM »
kiran rc
Plane Lover
Forum Hero

*****

Reputation Power: 21 
kiran rc barely matters.kiran rc barely matters.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Intermediate
Posts: 1260
Join Date: Feb, 2013

Live your dream and wear your passion



Do you use an external BEC for powering the cc3d or did you use the internal BEC of the esc inturn connected to the motor which is getting heated?Check the motor with the another esc.Check the connection between wires and connectors. And also check if the bell of the motor is freely moving.Some motors may have defective bearings.
Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
DYS BE1806-2300kv Motors [RED]
For Sale
charlie9165 5 2284 Last post February 07, 2016, 12:06:44 AM
by shivela39
For Sale DYS 1806 2300KV Motors with 20a ESC's Combo
For Sale
charlie9165 5 2772 Last post August 07, 2016, 02:21:07 PM
by rishabhbarma
4*Avionics RCB 2206-2300KV motors
For Sale
DRedemption 6 2543 Last post September 22, 2016, 07:59:58 PM
by DRedemption
2204 2300kv motors. 4 motors for 1800 free shipping
For Sale
tej 8 3153 Last post August 26, 2017, 02:01:52 PM
by tej
25x35cm Heat Resistant Heat Gun BGA Soldering Station Repair Insulation Pad
For Sale
Revanth9652 0 392 Last post May 16, 2021, 06:39:03 AM
by Revanth9652