|
Title: Hobbyking 30 Amp UBEC Programming Problem Post by: aditya on July 20, 2014, 03:20:55 PM I am trying to program Hobbyking 30 amp UBEC . I turned on Transmitter then moved throttle to full .After that connected ESC to receiver . After few seconds , 4 same beeps sound then 4 same beeps sound but different from first one , then i move throttle knob to zero . Now , throttle and break should be programmed . But no response , when i increase throttle . Although , all servo's are working fine . Can anyone suggest if ESC is not programmed properly or ESC is bad?
Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: aditya on July 28, 2014, 11:26:40 PM No one is using Hobbyking 30 A UBEC!!!
Is ESC bad or else? Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: tantragna on September 16, 2014, 04:48:41 PM Resolved the isse? if not, is this 30A ESC with UBEC or just 30A UBEC? You may try with trimming the throttle down towards zero, then the ESC should be calibrated..
Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: aditya on September 16, 2014, 05:16:20 PM Link to UBEc is :
http://www.hobbyking.com/hobbyking/store/__15205__hobby_king_30a_esc_3a_ubec.html (http://www.hobbyking.com/hobbyking/store/__15205__hobby_king_30a_esc_3a_ubec.html) Still not resolved .. Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: theleabres on September 17, 2014, 12:08:13 PM read the product manual. you have to enter the ESC programming mode first. then wait for the series of beeps.
Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: K K Iyer on September 17, 2014, 12:25:38 PM I turned on Transmitter then moved throttle to full. After that connected ESC to receiver . @aditya Connect ESC to battery. Rx should already be connected. Hope this helps. Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: aditya on September 17, 2014, 02:14:26 PM read the product manual. you have to enter the ESC programming mode first. then wait for the series of beeps. Sir , As per manual , by turning on transmitter with throttle in maximum positiion , ESC should be in programming mode . After Making connection few seconds later , 4 same beeps sound then 4 same beeps sound but different from first one , then i move throttle knob to zero . But no movement in motor while all servo's were working . I also checked motor with other ESC , motor was working fine.Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: aditya on September 17, 2014, 02:28:54 PM I turned on Transmitter then moved throttle to full. After that connected ESC to receiver . @aditya Connect ESC to battery. Rx should already be connected. Hope this helps. Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: K K Iyer on September 17, 2014, 03:08:10 PM @aditya
Try this: Move throttle to zero during first four beeps Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: sundaram on September 18, 2014, 01:07:14 AM Please do a throttle range first. Connect ESC with throttle Zero and after the initialization beep move throttle to full let it acknowledge with beep move throttle to zero now next time you move throttle then its should respond.
Now you can move to programming mode by keeping the throttle up and connecting ESC to battery and change the required setting by following steps as per the attached image. Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: tantragna on September 18, 2014, 03:16:31 AM Have you connected the esc to the correct port in the rx? Channel 3, which is a standard afaik!
Title: Re: Hobbyking 30 Amp UBEC Programming Problem Post by: aditya on September 18, 2014, 09:50:53 AM # Iyer sir & Sundaram Sir , Thanks . Will follow your steps and let you know.
# Tantragna sir , esc bec connected to Channel 3 . Thanks. |