Title: NEED HELP IN TURNIGY 25A ESC !!! Post by: arjun2592 on May 26, 2011, 08:24:56 PM HI ALL
i just received new esc it is Turnigy TY-P1 25Amp Brush-less Speed Controller using a 3s lipo 1050mah motor - cf 2822 1200kv outrunning now the battery is not yet fully charged ( using as bought ) i first connected the bind plug to the receiver and connected the esc to ch 3 also connected a servo to ch 1 ( for checking ) then turned the TX on then connected the lipo to the esc i got it bind successfully TX to Rx checked the servo ( it worked fine ) NOW THE PROBLEM IS THAT when i connect the motor to the esc and turned on the system on i hear the beep sound after it is set i gave a little throttle but there is no effect at all the motor didn't even move what could be the problem ??? what i think is : as it is an programmable ESC so it cuts the throttle at low voltage ( and as the lipo batt is not yet charged ) could it be an issue or i am wrong :headscratch: suggestion form all welcome :) :help: Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: anam_funny on May 26, 2011, 08:34:26 PM There is a signal problem. Try Ch2 and Ch3 both, sometimes the Throtle output is switched b/w the two channels.
Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: arjun2592 on May 26, 2011, 08:51:37 PM yea i tested it in ch 2 the motor moved a little and then rest
as it rest the esc started a rapid “beep-beep-, beep-beep sound ! and i also checked the esc manual it said If the very rapid “beep-beep-, beep-beep-” tones is emitted, means the input voltage is too low now how to bring it in ch 3 back or it will be OK in ch 2 :headscratch: Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: arjun2592 on May 26, 2011, 08:52:08 PM here is the manual
http://www.hobbywing.com/upload/manual/ESC_e.pdf Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: akky on May 26, 2011, 09:13:12 PM YOU HAVE TO PLUG THE esc INTO CHANNEL 3 CHANNEL 2 IS FOR ELEVATOR
Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: arjun2592 on May 26, 2011, 09:20:56 PM yes i tried it in ch 3 at first but there was no moment at all
as anam sir told (There is a signal problem. Try Ch2 and Ch3 both, sometimes the Throtle output is switched b/w the two channels. ) and i tried in ch 2 it worked the motor moved a little and the the esc started continues beep sound which i came to know after reading the manual that "If the very rapid “beep-beep-, beep-beep-” tones is emitted, means the input voltage is too low " now the thing is that the esc (throttle ) is working in ch 2 how to make it work in ch 3 :headscratch: i will charge the battery and then check it again will update the post after charging the battery thanks every one :) Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: akky on May 26, 2011, 09:35:43 PM WHICH RADIO ARE YOU USING...NEVR HEARD OF THROTTLE ON CHANNEL 2 :headscratch: :headscratch:
Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: anwar on May 26, 2011, 10:04:07 PM What's up with many using capital letters all the time now ? :headscratch:
Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: anam_funny on May 26, 2011, 10:09:52 PM That is happening in most of the HK radios, be it turnigy 9x or the latest 6DF. Akshay, you have used the futaba 7C, that is a good quality radio and does not have such problems...
If you are unaware of any such problem does'nt mean that it does not exists... And yes anwar bhai, I agree too... the all caps posts are a bit disturbing... Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: akky on May 26, 2011, 10:10:44 PM mine is 7C anam bhaiya
sorry for the caps lock ...i didnt noticet the caps as i am typing from my mobile sorry for the inconvenience caused Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: anam_funny on May 26, 2011, 10:15:04 PM I do not know why this defect is present in some radios... JUST A THOUGHT, can it be due to conversion of mode 1 to mode 2??
Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: arjun2592 on May 27, 2011, 10:37:12 AM the radio i am using is turnigy 9x
Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: saurabhhsrivastavaa on May 27, 2011, 12:09:52 PM After choosing "Stick Mode - 2", please calibrate your throttle for the ESC to run properly. Connect ESC to Channel 3. Calibration should be defined in the ESC manual.
Title: Re: NEED HELP IN TURNIGY 25A ESC !!! Post by: anam_funny on May 27, 2011, 12:42:14 PM When you select Stick Mode 2, it will ask you that you want to reverse the throtle. Click yes.
|