|
Title: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: dileepbalan on August 12, 2010, 08:45:57 AM Hi RC folks,
I brought the Turnigy Accucel-6 50W 6A Balancer/Charger from HK. http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=7028 Now I am in search for the power adaptor. Spec for my charger -------------------- Input Voltage: 11~17v Circuit power: Max Charge: 50W / Max Discharge: 5W Charge Current Range: .1~6.0A These are my plans... 1) Assemble a power supply. 12-0-12 txmr / 5A, converting to DC (full wace rectification). I hope DC voltage will be around 13.xx something. Is it good? Any better way / modifications please... 2) Heard from Sreedhar that, 12V Toshiba laptop charger is available. If I go for this, what are the spec I should check in the laptop charger? Any other similar chargers available? let me know you valuable suggestions. Regards, Dileep Title: Re: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: Bill on August 12, 2010, 08:59:25 AM Buy any laptop charger with output 12 V at least 60 to 70 W & see thst the output pin of the charger matches thi input jack on Your Accucel 6 - I have been running this setup for a very long time
Title: Re: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: praveen on August 12, 2010, 09:30:41 AM 1) Don't waste money on the txr and other circuit , i have done all those circus it will not work ,even slight higher or lower the voltage on charging ,it shouts like anything!
2) as adviced by 'Bill' purchase laptop power supply 12v,5 amp or make your own power supply using PC ATX SMPS ,that will be better , or enquire for universal laptop power supply which gives voltage from 12v-19v and 5 amp ! it is available in "Binary World" ,Bangalore cost around 650/- Title: Re: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: xxkrishxx on August 12, 2010, 09:58:52 AM Is it same for the Turnigy max 80w charger also?
Title: Re: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: praveen on August 12, 2010, 10:10:41 AM For 80W charger you can use 500W PC ATX SMPS it will work very well!
Title: Re: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: sandeepm on August 12, 2010, 10:46:48 AM Get the IBM Laptop Adapter
Title: Re: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: dileepbalan on August 12, 2010, 11:36:31 AM Thanks a lot for the suggestions. I just checked few chargers in office now
Lenovo charger - 20V 3.25A, 65W IBM thinkpad - 16V, 4.5Amp Hope I can get IBM charger from Ritchie street in Chennai Regards Dileep Title: Re: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: xxkrishxx on August 12, 2010, 11:43:23 AM Should i do any modifications in the smps?
Title: Re: Power adaptor for Turnigy Accucel-6 50W 6A Balancer/Charger Post by: vksingh on August 12, 2010, 12:39:04 PM Krish please refer earlier posts on SMPS Chargers
"http://www.rcindia.org/batteries-and-chargers/using-a-pc-smps-as-powersupply-for-rc-chargers/". |