Turnigy 2650mAh 3S 20C Lipo PackThe new Turnigy Lipoly packs deliver full capacity at the said C rate.
You wont find a better deal in Lithium Polymer batteries anywhere!
Spec.
Minimum Capacity: 2650mAh
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 20C
Peak Discharge (10sec): 30C
Pack Weight: 225g
Pack Size: 137 x 43 x 17mm
Charge Plug: JST-XH
Discharge Plug: Female XT60
BUY IT NOW :-
http://www.rcproduct.in/turnigy-lipoly-batteries/26-turnigy-2650mah-3s-20c-lipo-pack.htmlNew Items on RCP - RCProduct.in
ZIPPY Flightmax 4000mAh 3S1P 20CZippy Flightmax batteries deliver full capacity & discharge as well as being the best value batteries in the hobby market today!
Spec.
Capacity: 4000mAh
Voltage: 3S1P / 3 Cell / 11.1v
Discharge: 20C Constant / 30C Burst
Weight: 306g (including wire, plug & shrink wrap)
Dimensions: 146x51x22mm
Balance Plug: JST-XH
Discharge Plug: Bullet Connector
BUY IT NOW :-
http://www.rcproduct.in/batteries-accessories/15-zippy-flightmax-4000mah-3s1p-20c.htmlNew Items on RCP - RCProduct.in
ZIPPY Flightmax 2500mAh Transmitter Pack (Futaba/JR)The Zippy Flightmax 2500mAh Transmitter pack fits snuggly into any Futaba or Jr radio which takes a 4x4 AA cell battery configuration (see image).
With a capacity of 2500mAh this lipoly replacement for your old NiCD or NiMH will last four to five times longer. Probably the best advantage with a lipoly transmitter battery is that it will give a true voltage reading from start to finish which means you can say goodbye to the days where you thought your Transmitter was fully charged at home, only to find the voltage drop off rapidly when at the field.
Spec.
Capacity: 2500mAh
Voltage: 11.1v
Constant discharge: 3-5C
Burst discharge: N/A
Weight: 146g
Size: 100x28x23mm
Plugs: Futaba, JST-XH, JR/Spektrum
BUY IT NOW :-
http://www.rcproduct.in/transmitter-lipo-pack/20-zippy-flightmax-2500mah-transmitter-pack-futabajr.htmlNew Items on RCP - RCProduct.in
ZIPPY Flightmax 3000mAh 3S1P 20CZippy Flightmax batteries deliver full capacity & discharge as well as being the best value batteries in the hobby market today!
Spec.
Capacity: 3000mAh
Voltage: 3S1P / 3 Cell / 11.1v
Discharge: 20C Constant / 30C Burst
Weight: 239g (including wire, plug & shrink wrap)
Dimensions: 137x45x18mm
Balance Plug: JST-XH
Discharge Plug: XT60
BUY IT NOW :-
http://www.rcproduct.in/zippy-lipoly-batteries/25-zippy-flightmax-3000mah-3s1p-20c.htmlNew Items on RCP - RCProduct.in
Turnigy 9XR Transmitter Mode 2 (No Module)The greatly anticipated Turnigy 9XR has arrived!
The software for the 9XR first began development 6 years ago. Since then it has been tweaked, tuned, changed, updated and revamped by members of the R/C community into a powerful - yet easy to use interface. Our engineers designed the physical product around the R/C communities software changes and input. The culmination of all these is the Turnigy 9XR!
For many users this will be the perfect 9 channel radio straight out of the box, but there are many tinkerers out there who love modifying and pushing the boundaries of what is possible from their radio. We have factory fitted the 9XR with an AVR ISP header to simplify the development of custom software, we have launched turnigy9xr.com as the epicentre for software developers and additional community support for all 9XR users......With the 9XR we encourage it!
The 9XR is supplied preloaded with top quality software which is full of features and yet remains easy to use. Our aim was to develop a radio for you, the hobbyist, with an extensive list of standard features usually expected from a radio system 3 times the price. Our Turnigy 9XR is everything you imagined and more!
9XR Standard Features:
8 Channel PPM/9 Channel PCM
Full Ball Bearing gimbals
Adjustable Stick Length
Digital Trims on all Primary Axis
16 Model Memory
Assignable Switches
Freely Assignable Channel Mixes
Graphical Dual Rate and Exponential
Sub Trim and Travel Adjust
Flaps and Differential
Throttle Hold
Supports Heli/ Aero/ Glider Model Types
Programming Templates Based on Model Type
Supports M1, M2, M3, M4 stick modes
128 x 64 backlit Liquid Crystal Display
Built in JR & Futaba Trainer Ports
PPM & PCM Output
JR Form Factor RF Modules (Orx Dsm2, Orx Open LRS 433Mhz etc)
Programmable Timers
Low Voltage Warning and Buzzer
Supports 3s Lipo (Required)
9XR Firmware Pre-loaded
AVR ISP Interface
Internal 2.4GHz Antenna
Online support and user forums available at:
www.turnigy9xr.comSpec:
Channnel: 8ch ppm/9ch pcm
Display: 128*64LCD (Backlit)
Support Type: Heli/Acro/Glid
Model Memory: 16
Stick modes: 1, 2, 3, 4
Encoder type: ppm/pcm
Module Interface: JR Compatible (See Related Items Below)
Simulator Interface: Yes (JR & Futaba)
Buzzer: Yes
Battery Compartment: 112 x 44 x 27mm
Weight (less battery & Rf Module): 723g
Required:
Battery 3S Lipo
RF Module
Included:
Turnigy 9XR Transmitter (Mode 2 Throttle on Left Stick)
Quick Start guide
BUY IT NOW :-
http://www.rcproduct.in/2-4ghz-turnigy-india/8-turnigy-9xr-transmitter-mode-2-no-module.htmlNew Items on RCP - RCProduct.in
FrSky DJT 2.4Ghz Combo Pack for JR w/ Telemetry Module & V8FR-II RXFrSKY ACCST technology is proven, approved by many model associations, tested and reviewed as the leading Chinese 2.4Ghz R/C Technology. If you think DSM2 or FASST is the best, think again!
New FrSKY ACCST (Advanced Continuous Channel Shifting Technology) gives you secure radio communicatios in 2.4Ghz band. ACCST 2.4GHz system shifts 80 channels around hundred times per second in the 2.4GHz band. This means that the system is completely resistant to interference in that band.
Features:
Advanced Continuous Channel Shifting Technology (ACCSTis our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility.
Easy to bind and very fast link-up.
Excellent reboot time.
True Diversity with two antennas.
All channels can be programmed with Failsafe, quickly and easily.
Quick and extremely stable in performance.
Precise and smooth servo response.
Extended range (1.5km-2.5km).
FrSky DJT is compatible with JR transmitters following:
JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, PX, 9XII, 11XZERO
Receiver Specification:
Operating voltage: 3.0~16V(HV Version)
Power consumption: 30mA
Resolution: 3072
Latency: 22ms
Number of channels: 8
Range: 1.5km-2.5km
Dimensions: 44 x 24 x 14 mm
Weight: 9.3g
Module specification:
Operating voltage: 6.0V-13.0V (can handle 3S!)
Power consumption: 50mA
Output Power:: 60mW
Resolution: 3072 (11bit)
Dimensions: 63.9x48.5x36.5mm
Included;
1 x 8-channel Telemetry Transmitter Module DJT
1 x Transmitter Antenna
1 x 8-channel receiver V8FR-II (HV Version)
BUY IT NOW :-
http://www.rcproduct.in/frsky-accst-module-india/11-frsky-djt-24ghz-combo-pack-for-jr-w-telemetry-module-v8fr-ii-rx.htmlNew Items on RCP - RCProduct.in
Hobbyking KK2.0 Multi-rotor LCD Flight Control BoardDesigned by the Grand father of the KK revolution, Rolf R Bakke, exclusively for HobbyKing, the KK2.0 is the evolution of the first generation KK flight control boards. The KK2.0 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed. simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and your ready to go! all of which is done with easy to follow on screen prompts!
The original KK gyro system has been updated to an incredibly sensitive dual chip 3 Axis gyro and single chip 3 axis accelerometer system making this the most stable KK board ever and allowing for the addition of an Auto-level function. At the heart of the KK2.0 is an Atmel Mega324PA 8-bit AVR RISC-based microcontroller with 32k of memory. An additional 2 motor output channels have been added to the KK2.0 allowing for a total of 8 motors to be controlled (Octocopter). A handy Piezo buzzer is also included with the board for audio warning when activating and deactivating the board.
If your new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.0 was built for you. The 6 Pin USBasp AVR Programming interface ensures future software updates will be quick and easy.
Specs.
Size: 50.5mm x 50.5mm x 12mm
Weight: 21 gram (Inc Piezo buzzer)
IC: Atmega324 PA
Gyro: InvenSense Inc.
Accelerometer: Anologue Devices Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us
Firmware Version: 1.2
Pre-installed firmware.
Dualcopter
Tricopter
Y6
Quadcopter +
Quadcopter X
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Aero 1S Aileron
Aero 2S Aileron
Flying Wing
Singlecopter 2M 2S
Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option)
The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.
Whats is a Multi-Rotor Control board you ask?
The HobbyKing KK2.0 Multi-Rotor controller is a flight control board for multi-rotor Aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the three on board gyros (roll, pitch and yaw) then passes the signal to the Atmega324PA IC. The Atmega324PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft.
The HobbyKing KK2.0 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega324PA IC via the ail, ele, thr and rud inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).
BUY IT NOW :-
http://www.rcproduct.in/multi-rotors-parts/12-hobbyking-kk20-multi-rotor-lcd-flight-control-board.htmlNew Items on RCP - RCProduct.in
325mm Carbon Fiber Main Blades450 Size Carbon Fiber blades with reinforced root and balanced tip.
Spec;
Length: 325mm
Weight: 21g each
Grip : 5mm
BUY IT NOW :-
http://www.rcproduct.in/helicopters-parts/19-325mm-carbon-fiber-main-blades.htmlNew Items on RCP - RCProduct.in
WLtoys V911 - 2.4Ghz 4CH Micro Helicopter Mode 2 (RTF)WLtoys V911 2.4GHz 4CH Remote Control RC Helicopter with Gyro Mode 2
The new Hobbyking FP100 2.4Ghz 4CH micro helicopter is a high performance fixed pitch heli at an unbelievable price! (Compare this to the Align Trex 100)
The Hobbyking FP100 is a very capable fixed pitch heli with two flight modes - standard and high performance (selectable by button on top of radio). By swithing to high performance mode, the swashplate throws are increased which makes the heli much more agile and gives it faster response. This also allows this micro heli to handle less than calm wind conditions, so makes it suitable for outdoor use as well!
The included 2.4Ghz radio is extremely high quality with its easy to read, brightly backlit LCD display and digital trim adjustment. This is an exceptional value compared to low quality radios that are generally included in other ready to fly kits.
This ready to fly kit includes a spare main blade set, spare tail blade, 2 x 3.7V 120mAh lipoly batteries, a dual charger which can be powered via included USB cable, and also a charge lead built in to the radio for charging when no USB connection is available. All you need to do is charge the batteries and your ready to fly!
You will not find a better deal on the market today for a fixed pitch micro helicopter of this quality!
Specifications:
Length: 215mm
Height: 84mm
Gross Weight: 31g with battery
Battery: 1S 3.7V 120mah Li-Po
Transmitter: 2.4Ghz Mode 2 (Throttle on the Left)
Flight Duration: 6-8 minutes
Included:
FP100 4CH micro helicopter
2.4Ghz mode 2 rado w/backlit LCD display
2 x 3.7V 120mAh lipoly
Dual slot battery charger w/USB charge cord
Spare main blade
Spare tail blade
Required:
6 x AA size batteries
BUY IT NOW :-
http://www.rcproduct.in/ready-to-fly-rtf/18-hobbyking-fp100-24ghz-4ch-micro-helicopter-mode-2-rtf.htmlNew Items on RCP - RCProduct.in
New Items on RCP - RCProduct.in