Cheap AnyCopter Frames and Kits (Quad kits Under Rs.375)

Started by yashodhanp, March 18, 2014, 09:50:50 PM

Previous topic - Next topic

0 Members and 4 Guests are viewing this topic.

yashodhanp

Hey guys,
  I got some centre plates laser cut, that can be used to make all kinds of multirotors. (Tri, quad, hex and octacopters) based of the RotorBones Anycopter hub kit.

Pics attached.

Each set of centre plates will cost Rs. 90 + Rs. 70 (Flat rate S&H via EMS Pan-India upto 3 sets) (Discounts available for shipping beyond that. P.M. for further details)

Each set includes the laser cut centre plates ONLY(Top & Bottom Plate, Battery Mount and Boom Drilling Templates)

Booms and Other hardware NOT included. The hub has been designed to use 1/2" booms. Each set will come with a small sheet of paper with photos on the different types of setup possible.

Update: 1/2" Aluminium Booms can be included in the kit @ Rs. 1.5 per inch for custom sizes (kindly specify the size you wish your booms to be  :)  (nominal handling fee of Rs. 30 will be added to the final amount(discounts available for larger orders) ) or Rs. 15 for a standard 12" boom, undrilled(

Hardware Pack Constituting of 18 Stainless Steel M3 x 25 Philips head screws and 18 Regular Nuts also available @ Rs. 90 (No additional shipping charges for it)


Thus total kit can cost as little as Rs. 240 plus shipping for a standard Quad and slightly higher for other variants  ;D

N.B.: Actual hub kit from RotorBones costs $14 which is roughly Rs. 830 :o


Regards
Yashodhan
Sent from a potato using a lamp.

v2 eagle

Is that possible for you to make a custom cut with design given,
also what material is this and how much load can this bear,

Ashok.P
FPV with head goggles

http://ashokpkumar.wix.com/mysite

yashodhanp

Bump.

@ashok, the material used is 2.5mm pine HDF. It can support a good amount of load and will be stronger once booms are attached :D, certainly your own designs can be cut as well
Sent from a potato using a lamp.

VC

Yash, one complete set for a Hexa that will measure 36" from spinner tip to spinner tip. Let me have a quote on this please. Inclusive of 6 aluminium booms, screws and nuts, centre plates etc. Would prefer to have the booms drilled for fitting. Also will need 6 smaller circles of 1.5" dia to be drilled and screw fitted at the tip of every boom (as motor mounts).

Thanks.
Growing old is mandatory, growing up is optional!

yashodhanp

A 36"  MtM hex with all that you have asked for would cost you Rs 425+ 100 S&H

The Kit will include:

1. Centre Plates x 1
2. 18" x 1/2" Booms x 6 (predrilled for the centre plates, pls drill motor mounts yourself as per your requirements)
3. 1.5" discs for motor mounts x 6
4. The Hardware pack consisting of 18 M3 Screws and Nuts. (Not enough for motor mounts and motors)

Additional hardware available at extra (special) cost of Rs. 80 for additional sets of screws (18 of each)

   


Sent from a potato using a lamp.

VC

What is the dia of the centre plate and what length of the 18" boom will be bolted above/below it? I am trying to reach 36" tip to tip, therefore if the centre plate has a 6" dia and 2" of the boom is screwed in then I am left with 16" + 6" + 16" = 38" tip to tip measurements. That suits me fine as I plan on using 10" props.

All else that you have quoted is PERFECT!
Growing old is mandatory, growing up is optional!

yashodhanp

The diameter is roughly 5 inches and each boom is bolted 1"  into the centre plates thus giving a tip to tip of 39" 17 + 5 + 17= 39"

Pls. Don't me me cutting you, you said 36" spinner tip to spinner tip, so only if you plan to install half the motor mount on the boom will the 36" tip to tip work, while if you wish to install the entire motor mount you would need an additional .75" (17" boom)  and I chose 18" only because it's in multiples of 1/2 a foot :)
Sent from a potato using a lamp.

VC

Thanks will it be possible to let me have 8" dia centre plates and 16" tubes. I would like 2" of tube bolted into the plates.

Or even 8" dia plates and 18" tubes with 3" bolted in will do.
Growing old is mandatory, growing up is optional!

yashodhanp

I am really sorry, but 8" centre plates won't be possible :)
Sent from a potato using a lamp.

yashodhanp

A standard quad kit is available at Rs. 350. INCLUSIVE of Shipping and Handling a Across. India.

The Kit will include:

1. Centre Plates x 1
2. 12 x 1/2" Booms x 4(predrilled for the centre plates, pls drill motor mounts yourself as per your requirements)
3. 1.5" discs for motor mounts x 4
4. The Hardware pack consisting of 18 M3 Screws and Nuts. (Not enough for motor mounts and motors)

Additional hardware available at extra (special) cost of Rs. 80 for additional sets of screws and nuts (18 of each)

   
Sent from a potato using a lamp.

VC

Rs.350/- for an ARF Quad frame? ??? Yet no takers? ???

Let me be the first one - One for me please. Will remit in a while.
Growing old is mandatory, growing up is optional!

yashodhanp

Sure, will ship it tomorrow/day after. Kindly PM/Whatsapp your address :D
Sent from a potato using a lamp.

yashodhanp

Anyone interested in the quad kit?
P.S. i am asking this,  so that i can kit them out together.
Sent from a potato using a lamp.

v2 eagle

Need a 2xTricopter center plate and 3xbumble bee motor mount, will send you the template(the same rcexplorer.se david windestal template) by today, PM me your email ID and bank acc no, need a quote on the same with shipping to chennai(Speed post only)

Ashok.P
FPV with head goggles

http://ashokpkumar.wix.com/mysite

yashodhanp

Bump. Anyone else interested in the quad kit @350/- inclusive of shipping across india ??
Sent from a potato using a lamp.

roby

is it a 350mm frame?
was wondering if you can make a 450mm?
what's the charge inclusive of shipping?

yashodhanp

#16
No. The quad is 27" MtM, that would cost 375/- inclusive of shipping.
Sent from a potato using a lamp.

yashodhanp

Custom Orders Received from "Sidewinder" and "v2_eagle". Will quote prices by tomorrow 9AM

Regards
Sent from a potato using a lamp.

yashodhanp

Update: Pricing revised to 375/- for the Quad Kit, due to certain calculation errors I misquoted @350/-. Pls use the other thread to place orders for the Quad.

Regards
Sent from a potato using a lamp.

roby

Where is the order thread? I think I sent you pm long back?

yashodhanp

Check the post in the sales area just below this one.
Sent from a potato using a lamp.

SideWinder


yashodhanp

Hello, I am sorry for the delay, can you please allow me to give your quotes tomorrow morning first thing?
Sent from a potato using a lamp.

SideWinder

Please take your time, just thought of reminding you incase you forgot about it.

yashodhanp

No no.. My laptop is giving some troubles :( hanging frequently.
Sent from a potato using a lamp.

rcpilotacro

one for me, incl extra hardware for the motor mounting
Gusty's Hangar and Introduction.

A Good pilot will practice until he gets it right,
A Great pilot will practice until he can't get it wrong.

yashodhanp

Another set reserved for Gusty Ji. (@gusty ji I request you pls give me time till Tuesday to ship out your order)
Sent from a potato using a lamp.

yashodhanp

Sent from a potato using a lamp.

roby


Shyam Hembram

Yashodhanp can u make 450size frames like reptile or deadcat,etc,will be first to place order.just curious if you could do that???
Hiller450 chopper,Sky surfer v2,Wilga2000,450quad(building)

yashodhanp

Sent from a potato using a lamp.

yashodhanp

#31
Hi guys,

     Instead of the previous Quad Kit, i have made another quad kit which is a lot easier to assemble and use.

The kit is Priced at Rs. 350 + Rs. 90 (Flat Rate Shipping and handling across India)

The kit will include:

1. The Kit
2. 32 Screws and Nuts (adequate for everything)
3. 6/8 mm sq. wood for reinforcements and landing gear.

The battery can be suspended via battery straps, but you will have to provide a landing gear if you wish to.

The Control Board holes are spaced 45mm apart (KK standard) and are easily switched between + and X. You may use foam tape to mount other sizes.

Spares (Booms and Centre Plates) will be available at extremely reasonable prices as well

I am making this available only on a preorder (shipping commencing on Wednesday/Thursday) since i need atleast 5-7 orders for the kit to make it economical.

Ideal for people wanting to try multirotors on the cheap :)

Discounts available on orders above 3 pieces

Regards
Sent from a potato using a lamp.

manojswizera

good Yash.
what material is used for booms ? and its thickness.
Russ-40 Trainer, Mr.moss, Pushler, Skysurfer, Mugi , F-22, Red swan, Xtra-300, redfury, flying mantaray.

yashodhanp

Its all 2.5mm HDF, it will be reinforced using 6/8mm wood square rods glued to it.

Regards

Sent from a potato using a lamp.

Ahamed

I need one kit how much and how soon can u deliver at Hyderabad

Sent from my Nexus 4 using Tapatalk
Bixler2, FLYSKY, THX 9, 9XR, DX6i, Techone Satrun, Multiplex FunCub, FunJet, FRSKY DJT

yashodhanp

Sent from a potato using a lamp.

yashodhanp

#36
Bump for the Anycopter frame only. (aluminium booms undrilled also possible).
Orders for the 450mm quad taken as well(@400 all inclusive of shipping!!)  :hatsoff: (PM for discounts)
Sent from a potato using a lamp.

GreenBrains

Hi,

Can you build a Octocopter Frame like this?... Tarot IRON MAN1000 8 aix octocopter TL100B01 Frame Kit

http://www.hobbyking.com/hobbyking/store/__54327__tarot_iron_man_t1000_octo_copter_carbon_fiber_frame_kit_tl100b01.html

Any other custom designed and manufactured but stable and strong 800-1000 mm OctoCopter Frame will do, please let me know if anyone have it new or used.

I wanted to use it for Professional Aerial Photography Octocopter.

If anyone have it, please contact me ASAP.

Thanks & Regards,
Nilesh Shinde

Ph.: 07588578939
Nilesh Shinde

blackhawk_sourav

Hi, can you give a quotation for 450 mm quad - centre plates with aluminium square rods and all required screws. Am from kolkata and a newbie in this hobby.

Thanks & Rgds,
Sourav


teamnamibia

Hey Yashod, how much will you sell aluminium boom rods for?
forever indebted to this community. :-) currently in Namibia, let me know if you guys want to come over!