|
Title: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 02, 2016, 10:57:30 AM Hi all,
Hiller Hover kit from rc bazaar..it is my first Heli Electronics: ESC:Emax 40A Esc MOTOR:Avionic PRO H2217 KV4000 FOR 450 HELI brushless motor www.rcbazaar.com/product.aspx?productid=4114 SERVOS:Avionic AV9A 9g Servo 3 Tail servo: http://www.hobbyking.com/hobbyking/store/__22687__Turnigy_8482_TGY_306G_Ultra_Fast_High_Torque_DS_MG_Alloy_Cased_Servo_3kg_0_06sec_21g.html GYRO:ASSAN GA250 http://www.hobbyking.com/hobbyking/store/__15318__HobbyKing_GA_250_MINI_MEMS_Gyro.html i will post all build pics here. iam new to Heli please give me your suggestions if you find anything wrong in my build Thank you all Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 02, 2016, 11:00:55 AM tail boom belt and motor installed
Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 02, 2016, 11:26:51 AM servo ball links installed..
is it right or wrong ???? Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: saikat on February 02, 2016, 12:13:03 PM looks wrong ...
all your servo arms should be at the same position with the swash flat. couple of tips a . dowload the manual for align trex 450 and see how to set up your swash. b. google for and watch the finless bob videos for setting up a flybar heli. Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 02, 2016, 03:02:57 PM @saikat thank you
adjusted servo ball links only one servo link not proper any suggestions to adjust that Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: Hellyflyer on February 03, 2016, 10:36:10 AM only one servo link not proper any suggestions to adjust that Swap the linkage rod to ensure you have the correct one for this servo. Remove linkage rod to ensure servo is centered place the servo horn parallel to the swash as much as possible. Place the correct size linkage rod for this servo. Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 03, 2016, 01:56:55 PM @
Hellyflyer thank you I have doubt ..while center these control horns my throttle stick should be in center or at 0 throttle??? because i did all servos when throttle at 0 confused???? Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: dhruvafreak on February 03, 2016, 04:25:27 PM Keep the throttle stick centered while centering the servos.
Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 03, 2016, 04:37:32 PM @dhruvafreak thank you very much. i will do that today...:)
Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 03, 2016, 11:30:28 PM servos centered .one servo not exactly centered
now i need to level swashplate.. can i use subtrims to level swash plate? Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 04, 2016, 04:25:09 PM To level swaplate do i need to use subtrims or ajust pushrods...how to level swashplate :headscratch: :headscratch: :headscratch:
Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: tantragna on February 05, 2016, 08:58:53 AM If the corrections is limited to couple of degrees, you can do with the sub-trims, if greater than 5degrees, then better do it at the push rods. To level a swash plate, a swash plate leveller is needed and they are specific to each heli and pretty expensive. If you don't have one, then you have to look around for the alternatives around you.
Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: ramarao on February 05, 2016, 10:08:28 AM @tantragna thank you :) :) :) :)
Title: Re: Hiller Hover 450 Heli build-my first Heli Post by: Hellyflyer on February 16, 2016, 02:31:48 AM check on youtube for how to make swash leveler from zip tie
I Agree with Tantragna |