RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: June 09, 2018, 02:20:21 PM »
Imperial fire
Plane Lover
Forum Hero

*****

Reputation Power: 11 
Imperial fire has no influence.
Offline Offline

City: Sangamner
State: Maharashtra
RC Skills: Intermediate
Posts: 662
Join Date: Feb, 2017

Keep calm and fly safe.




Hey can anyone tell me where to connect the fsia6 rx output to the betaflight f4?
The fsia6b Rx has ibus output...
Should that output go to the sbus pads on the f.c? Or to the dsm2 pads?
Also what UART should I enable in the setup for the same?
 
I have currently connected it to the sbus pad and enable UART 6. But the f.c won't respond to any transmitter input in the receiver section...
Yes I have enabled ibus in the port section...
P.s I am using the fsi6 radio.
Logged
 

Read
« Reply #1 on: June 09, 2018, 05:33:29 PM »
Imperial fire
Plane Lover
Forum Hero

*****

Reputation Power: 11 
Imperial fire has no influence.
Offline Offline

City: Sangamner
State: Maharashtra
RC Skills: Intermediate
Posts: 662
Join Date: Feb, 2017

Keep calm and fly safe.



okay so ive been working on this non stop all day...its all ready..
i am confident that the sbus port and the ibus ports are the same.

PROBLEM IS my quad wont arm . when i connect it to the software on pc it says arming disabled.

also the receiver tab doesnt respond to any transmitter throttle etc changes

yes i have activated serial rx for uart 6 and selected the correct options in ports tab for ibus.
what have i missed.??
Logged
 

Read
« Reply #2 on: June 10, 2018, 02:01:59 PM »
SK1701
Heli Lover
Forum Hero

*****

Reputation Power: 11 
SK1701 has no influence.
Offline Offline

City: Montreal/ Bangalore
State: OUTSIDE INDIA
RC Skills: Intermediate
Posts: 888
Join Date: Oct, 2014

set acc_hardware = 1



1. Make sure only Serial Rx is enabled on the UART corresponding to the SBus pad
2. Make sure IBus is selected as the serial receiver protocol in the configuration tab
3. Make sure serial rx inversion is off in CLI. IBus is not an inverted protocol (like SBus) as far as I know
Logged

 

Read
« Reply #3 on: June 11, 2018, 07:32:47 AM »
Imperial fire
Plane Lover
Forum Hero

*****

Reputation Power: 11 
Imperial fire has no influence.
Offline Offline

City: Sangamner
State: Maharashtra
RC Skills: Intermediate
Posts: 662
Join Date: Feb, 2017

Keep calm and fly safe.



I forgot to do step 3 ..but then I decided to put my ibus in a different UART that did not have inversion...so it ended up working fine.
Thanks for the tip . I had zero clue as a beginner took me forever to figure it out.
Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
NEED HELP WITH FPV WIRING
Servos, Gyros and All Electronics
muradshak 9 7709 Last post August 02, 2013, 11:32:10 AM
by satyagupta
NAZE 32 and 12A ESC- wiring?
Multirotors
anilntny 5 3611 Last post January 01, 2016, 11:39:09 AM
by ilyas ali
Need BetaFlight Controller
Wanted
ajeetk 2 1617 Last post October 17, 2017, 02:02:04 PM
by pixelshooter
0V Showing in betaflight configurator
Beginners Zone
Nkkr77 0 1653 Last post January 01, 2018, 04:51:02 PM
by Nkkr77
need help with betaflight remapping
Multirotors
Imperial fire 2 1199 Last post July 12, 2018, 06:44:14 PM
by kn8alpha