RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: May 11, 2014, 06:55:18 PM »
ruhul786
Heli Lover
Active Member
**

Reputation Power: 1 
ruhul786 has no influence.
Offline Offline

City: UK
State: OUTSIDE INDIA
RC Skills: Beginner
Posts: 20
Join Date: May, 2014




Hello,
I am trying to fly my quadcopter x525 using kk 2.0 and FrSky D8R-II PLUS and turnigy 9xr and FrSky DJT 2.4Ghz but when i go to receiver test mode ,there is no signal except aileron
and when i move right stick aileron value change only though i connected first channel (aileron) to the first slot, the second channel (elevator) to the second slot, the third channel (throttle) to the third slot , the fourth channel (rudder) to the fourth slot and the fifth channel (auxiliary) to the fifth slot but no signal :confused:
please see this following link       

Any help would be greatly appreciated.
Regards

WP_20140510_001.jpg
KK 2.0 Setup Reciever Issues NO SIGNAL help!
* WP_20140510_001.jpg (35.73 KB, 449x800 - viewed 3099 times.)
This post has 3 more images(s)/attachment(s). Please login or register to view them.
Logged
 

Read
« Reply #1 on: May 11, 2014, 07:02:36 PM »
maahinberi
Plane Lover
Forum Hero

*****

Reputation Power: 7 
maahinberi has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Beginner
Posts: 611
Join Date: Feb, 2011

In Thrust, I Trust


Re:

How have you connected the receiver to the kk2 board? The signal wires should be towards the screen. Post a pic of the connections if possible
Logged

Maahin Beri - Introduction and Hangar
Seagull Arising Star, Seagull Low Wing 40, AviSport (SPAD), Phoenix Scanner, VortexRC Speedster, Martian 220 Racing Quadcopter.
 

Read
« Reply #2 on: May 11, 2014, 07:32:52 PM »
utkarshg13
Plane Lover
Forum Hero

*****

Reputation Power: 11 
utkarshg13 has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Intermediate
Posts: 982
Join Date: Jul, 2013



Friend the signal wire(white or yellow one) in both cases i.e. ESC connections and receiver connections should be towards screen.
Logged

"If you were born with wings, do every thing you could, for flying."
 

Read
« Reply #3 on: May 11, 2014, 08:02:15 PM »
ruhul786
Heli Lover
Active Member
**

Reputation Power: 1 
ruhul786 has no influence.
Offline Offline

City: UK
State: OUTSIDE INDIA
RC Skills: Beginner
Posts: 20
Join Date: May, 2014



First 2 servo extensions are 3 wires and rest of them are 1 wire ( aileron and elevator ) .i uploaded some pictures
I noticed when I connected 3 wires servo and when I move left stick it does change elevator value up to 5
Before it was no signal.What should I do now.
Looking forward to hear from you
Many Thanks 

WP_20140511_006.jpg
Re: KK 2.0 Setup Reciever Issues NO SIGNAL help!
* WP_20140511_006.jpg (42.09 KB, 449x800 - viewed 3003 times.)
This post has 3 more images(s)/attachment(s). Please login or register to view them.
Logged
 

Read
« Reply #4 on: May 11, 2014, 08:07:22 PM »
ruhul786
Heli Lover
Active Member
**

Reputation Power: 1 
ruhul786 has no influence.
Offline Offline

City: UK
State: OUTSIDE INDIA
RC Skills: Beginner
Posts: 20
Join Date: May, 2014



Right now i don't have any spare servo cables i will get on Thursday.I had one spare servo extension cable
when i connected i got elevator signal .
Looking forward to hear from you
Many Thanks 
Logged
 

Read
« Reply #5 on: May 11, 2014, 08:08:21 PM »
ruhul786
Heli Lover
Active Member
**

Reputation Power: 1 
ruhul786 has no influence.
Offline Offline

City: UK
State: OUTSIDE INDIA
RC Skills: Beginner
Posts: 20
Join Date: May, 2014



right now i don't have any spare servo cables i will get on Thursday.I had one spare servo extension cable
when i connected i got elevator signal .
Looking forward to hear from you
Many Thanks  
Logged
 

Read
« Reply #6 on: May 11, 2014, 08:14:51 PM »
utkarshg13
Plane Lover
Forum Hero

*****

Reputation Power: 11 
utkarshg13 has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Intermediate
Posts: 982
Join Date: Jul, 2013



Hi, I hope you are opening many threads for the same thing. Please stick to one.
Now, you need atleast two servo extensions for connecting your receiver to the kk board. One goes to channel1-aileron on both normally. The other cable has to be connected vertically only on the signal pins. So, you can make 3 connections(elevator, throttle, rudder) from one cable only.
Logged

"If you were born with wings, do every thing you could, for flying."
 

Read
« Reply #7 on: May 12, 2014, 12:17:39 AM »
maahinberi
Plane Lover
Forum Hero

*****

Reputation Power: 7 
maahinberi has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Beginner
Posts: 611
Join Date: Feb, 2011

In Thrust, I Trust



In the closeup of the KK2 board, I noticed that the 3 wire servo extensions are fine, but you have connected the single wire black leads on the outer pins. As I said before, all signal wires should be towards the screen. Shift those black wires on the pins towards the screen. Even on the receiver side, those wires are connected to the ground pins. Keep the black wires on those pins where the signal (or white) wire of the 3 wire cable goes. You are currently only connecting the ground pin of the receiver (for channel 3, 4, 5) to the ground pin of KK2. So shift those wires on both sides.
Logged

Maahin Beri - Introduction and Hangar
Seagull Arising Star, Seagull Low Wing 40, AviSport (SPAD), Phoenix Scanner, VortexRC Speedster, Martian 220 Racing Quadcopter.
 

Read
« Reply #8 on: May 12, 2014, 01:18:41 AM »
utkarshg13
Plane Lover
Forum Hero

*****

Reputation Power: 11 
utkarshg13 has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Intermediate
Posts: 982
Join Date: Jul, 2013



Hi,
In your case its only the wrong connections. Please go through very carefully now.
A small briefing first, please keep the receiver and KK2 board before you to have a better understanding. The order of the three wires in your receiver is signal(W), VCC(R), ground(B) where signal comes on top and ground should be on lower side of receiver. Now comes the KK2 board. Here, also order remains same but thats the mirror image. So now, its like signal(w) facing screen or near screen, VCC(R) in middle, and ground(B) on the outer edge. It could be easily understood on the KK2 manual available at HK(hobbyking) website.
Since, I hope now you are familiar with the connections, now comes connecting your board to receiver. I could see two jumpers with you. You need only those two for making connections, just be very careful while making connections.
The receiver is powered with the help of these jumpers through KK2. So, the first jumper has to be connected to the aileron channel both in receiver and KK2. Be sure of making connections and the pins.
"Black wire would got to outer edge of KK2 and the other end would go to lower side of receiver in the aileron channel. Similarly, red wire in
middle in both and white wire would come on top in receiver and towards screen in KK2." Now since, you're done with aileron jumper so comes other ports as well. Now you need to connect elevator, throttle and rudder.
This is done by connecting the three pin jumper vertically in both(Rx and KK2). These connections are to be made only on signal pins and it would be like signal wire(w) would go to signal pin of elevator(in Rx) and other end to signal pin of elevator (in KK2), VCC(R) wire would go to signal pin of throttle(in RX) and other end to signal pin of throttle(on KK2) and ground(B) would go to rudder on both similarly.

 Hats Off
Logged

"If you were born with wings, do every thing you could, for flying."
 

Read
« Reply #9 on: May 13, 2014, 05:00:59 AM »
ruhul786
Heli Lover
Active Member
**

Reputation Power: 1 
ruhul786 has no influence.
Offline Offline

City: UK
State: OUTSIDE INDIA
RC Skills: Beginner
Posts: 20
Join Date: May, 2014



Thank you very much for your help. Really appreciate it. Clap
I got all the signals now ( Aileron,Elevator,Throttle,Rudder and Auxiliary ) only problem is  rudder channel value always stay negative e.g. -5, -1 etc. So i did change my controller setting (turnigy 9xr ) i went to limits mode and changed channel 4 value 0.0 to 0.5  Grin and i got positive value (i hope i did right thing ? )
Right now motors are working when i turn on my controller and then i turn on kk board .Its shows armed and that time motors works
but if i turn on kk board first then controller then kk board shows error no yaw input ? could you please explain it to me why it shows error when i turn on kk board first. Also i noticed when i move my controller sticks 4 motors doesn't work together ? (1/2 at a time )
if i am not mistaken 4 motors should works together isn't it? although i did set up motor layout to quadcopter x  Huh?
Looking forward to hear from you .
Regards
Ruhul

IMG_3871.jpg
Re: KK 2.0 Setup Reciever Issues NO SIGNAL help!
* IMG_3871.jpg (41.89 KB, 598x800 - viewed 2952 times.)
This post has 1 more images(s)/attachment(s). Please login or register to view them.
Logged
 

Read
« Reply #10 on: May 13, 2014, 09:03:57 AM »
utkarshg13
Plane Lover
Forum Hero

*****

Reputation Power: 11 
utkarshg13 has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Intermediate
Posts: 982
Join Date: Jul, 2013



So finally you got all signals. Thumbs Up Thumbs Up
Now since rudder channel is having negative number for that you can adjust it to 0 by adjusting rudder trim from your transmitter and its done. Second thing you mentioned is not clear. On connecting battery does it shows ARMED or you yourself arm your board(by shifting rudder stick bottom right). The correct procedure is always first turning your transmitter on and then plugging in battery.
Also, since your motors are not working together kindly recalibrate your ESC's. I hope you are familiar to this. Before calibrating do not give throttle.
I think  you should go through youtube and search for: Die hard RC  addicts SK450 quadcopter part 2 setting up.
This is very helpful. I'm sure you'll get all your answers here.

 Hats Off
Logged

"If you were born with wings, do every thing you could, for flying."
 

Read
« Reply #11 on: May 13, 2014, 09:06:32 AM »
utkarshg13
Plane Lover
Forum Hero

*****

Reputation Power: 11 
utkarshg13 has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Intermediate
Posts: 982
Join Date: Jul, 2013



I think I got the link. Go through part 1, 2 and 3 to have a thorough idea.



 Hats Off
Logged

"If you were born with wings, do every thing you could, for flying."
 

Read
« Reply #12 on: May 14, 2014, 06:15:40 AM »
ruhul786
Heli Lover
Active Member
**

Reputation Power: 1 
ruhul786 has no influence.
Offline Offline

City: UK
State: OUTSIDE INDIA
RC Skills: Beginner
Posts: 20
Join Date: May, 2014



Thank you my friend .I did check that youtube video and i follwed their instruction with regards to ESC calibration but unfortunatley after 2 beeps when i move throttle down it shows ESC Calibrating and nothing happen.I hold first and last button more then 5 minutes but nothing happen.I noticed when i go to receiver test or kk board setting mode 3 motors move except 1 motor.I guess that motor is not working therefore ESC Calibration isnt working .What do you think ?? even yesterday when it was armed 4 motors was working though it wasn't working together.
Looking forward to hear from you :-(
Ruhul
Logged
 

Read
« Reply #13 on: May 14, 2014, 06:26:29 AM »
v2 eagle
AK
Plane Lover
Forum Hero

*****

Reputation Power: 12 
v2 eagle has no influence.
Offline Offline

City: chennai
State: Tamil Nadu
RC Skills: Beginner
Posts: 1178
Join Date: Jun, 2013



Check the motor/esc individually whether they are working fine by connecting directly to RX.If they are working fine, then you can calibrate them individually with RX and then connect them to KK board.
Logged

 

Read
« Reply #14 on: May 14, 2014, 06:43:20 AM »
ruhul786
Heli Lover
Active Member
**

Reputation Power: 1 
ruhul786 has no influence.
Offline Offline

City: UK
State: OUTSIDE INDIA
RC Skills: Beginner
Posts: 20
Join Date: May, 2014



Thanks for your comment .I can also check with multimeter also isnt it ? for example please see this video (just to confirm )

Logged
 

Read
« Reply #15 on: May 19, 2014, 05:52:09 AM »
ruhul786
Heli Lover
Active Member
**

Reputation Power: 1 
ruhul786 has no influence.
Offline Offline

City: UK
State: OUTSIDE INDIA
RC Skills: Beginner
Posts: 20
Join Date: May, 2014



Thank you guys ,now that motor is working ,cable connection was lose that's why it didn't work before.However 4 motors are working fine when throttle full upward but my quadcopter doesn't lift off ,any suggestion
please check my video



Regards
Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
PPM Signal in My Tx
Radios and Receivers
sandeepm 5 5206 Last post October 05, 2009, 09:43:56 AM
by sandeepm
USING A UBEC to power a reciever in an electric setup
RC General Topics
avijit17basu 4 6613 Last post January 20, 2010, 09:43:16 AM
by sushil_anand
Controlling two servos with same signal
Radios and Receivers
Swapnil 13 7101 Last post June 04, 2011, 12:19:45 PM
by Swapnil
QUADCOPTER AND SERVO SIGNAL
RC General Topics
ATLAB 2 2483 Last post June 30, 2013, 02:49:44 PM
by Rahulvyas
Flysky fs T6 (Signal Issues)
For Sale
kenistan 0 352 Last post August 08, 2021, 12:01:10 AM
by kenistan