RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: February 03, 2013, 07:41:57 PM »
sathish kumar
Plane Lover
Active Member

**

Reputation Power: 1 
sathish kumar has no influence.
Offline Offline

City: chennai
State: Tamil Nadu
RC Skills: Beginner
Posts: 55
Join Date: Feb, 2013




Hi...iam using kk 2.0 flight contrlr brd.it is showing ERROR : NO THROTTLE SIGNAL.wat should I do?

DSC_0120.jpg
kk board error
* DSC_0120.jpg (34.33 KB, 800x600 - viewed 459 times.)
Logged
 

Read
« Reply #1 on: February 03, 2013, 09:34:13 PM »
jaspreet.guitar
Heli Lover
Senior Member
***

Reputation Power: 4 
jaspreet.guitar has no influence.
Offline Offline

City: Noida
State: Uttar Pradesh
RC Skills: Beginner
Posts: 177
Join Date: Feb, 2012



Switch on the Radio first and then switch on the KK board.
Logged
 

Read
« Reply #2 on: February 03, 2013, 09:53:52 PM »
sathish kumar
Plane Lover
Active Member

**

Reputation Power: 1 
sathish kumar has no influence.
Offline Offline

City: chennai
State: Tamil Nadu
RC Skills: Beginner
Posts: 55
Join Date: Feb, 2013



Thanks for ur reply..i tried ur suggestion but it remains the same..
Logged
 

Read
« Reply #3 on: February 04, 2013, 04:29:49 PM »
SunLikeStar
Forum Administrator
Forum Hero

*****

Reputation Power: 20 
SunLikeStar barely matters.SunLikeStar barely matters.
Offline Offline

City: Pune
State: Maharashtra
RC Skills: Intermediate
Posts: 1902
Join Date: Aug, 2010

High spirits we have: gravity we flout.



Confirm if your receiver is binding/working. If its working properly then turn on your radio first then your multicopter. If still getting error then disconnect power from multicopter and reconnect again. If still getting error then post picture of connection on your KK board.
Logged
 

Read
« Reply #4 on: February 07, 2013, 12:10:40 AM »
atulrajguru9
Plane Lover
Forum Veteran
****

Reputation Power: 5 
atulrajguru9 has no influence.
Offline Offline

City: Pune
State: Maharashtra
RC Skills: Beginner
Posts: 337
Join Date: Nov, 2010



Try to trim down your throttle  .... may be FC is not getting min throttle
Logged
 

Read
« Reply #5 on: February 07, 2013, 12:41:14 AM »
VC
Boat Lover
Forum Hero

*****

Reputation Power: 64 
VC is a rising star!VC is a rising star!VC is a rising star!VC is a rising star!VC is a rising star!VC is a rising star!
Offline Offline

City: Guwahati
State: Assam
RC Skills: Beginner
Posts: 5598
Join Date: Nov, 2009

L'enfant Terrible du RCIndia



Have you tried moving your sticks left right / right left? It seems like that it is stuck on 'safe' mode and that it is not 'armed". Btw, what Tx/Rx  are you using?

You have to move and hold the right stick (Mode 2 Tx) either to the left or right for a few (5) seconds to disarm it and get out of 'Safe' mode.
Logged

Growing old is mandatory, growing up is optional!
 

Read
« Reply #6 on: February 07, 2013, 09:43:59 AM »
KALYANPRODHAN
Global Moderator
Forum Hero

*****

Reputation Power: 17 
KALYANPRODHAN has no influence.
Offline Offline

City: Kolkata
State: West Bengal
RC Skills: Intermediate
Posts: 1584
Join Date: Jul, 2010

Information sharing improves knowledge of both.



Throttle channel are connected elsewhere in receiver. So, kk2 multocopter board not get initially zero throttle initially (eg, rudder,elevators are center positioned and gives 50% position signal during start). Hope you will get it solved early.

Good Luck.
Logged

We have to unite and to prove ourself to make indigenous products as well as marketing / Canvasing them. I'm sure we must achieve success if we try unitedly.
 

Read
« Reply #7 on: February 07, 2013, 06:27:19 PM »
sathish kumar
Plane Lover
Active Member

**

Reputation Power: 1 
sathish kumar has no influence.
Offline Offline

City: chennai
State: Tamil Nadu
RC Skills: Beginner
Posts: 55
Join Date: Feb, 2013



hi guys...thanq very much for al ur suggestions...   Bow ...i sent back that board to the store for replacement..
Logged
 

Read
« Reply #8 on: February 13, 2013, 07:26:08 PM »
DhruvChavan
Heli Lover
Active Member

**

Reputation Power: 2 
DhruvChavan has no influence.
Offline Offline

City: Mumbai
State: Maharashtra
RC Skills: Beginner
Posts: 85
Join Date: Nov, 2012

drop a message on 8655448398 :)



lol this happened to me but i found out i didn't push the servo pins all the way in. anyways hope u gt it back soon Smiley
Logged

Flysky Th9x
Custom body quadcoptor.
FT3D, Old Foggy, 
Photographer, Editor, Football freestyler, Cyclist,
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
JVC Video camera HDD Error
Chatter Zone
Sahevaan 2 2927 Last post June 11, 2010, 08:10:05 PM
by Sahevaan
homemade brushed esc error
Self-designed, DIY and College Projects
rc ram 6 12459 Last post November 13, 2012, 12:56:27 PM
by KALYANPRODHAN
Error: Joystick could not be found « 1 2  All »
Radios and Receivers
GreenBrains 28 16318 Last post June 15, 2013, 01:07:04 PM
by girishsarwal
KK2 Board Error
Multirotors
pravinxp 6 5383 Last post October 25, 2013, 11:53:13 AM
by arun.sreelakam
Problem Or Error in programming STM32 board with FTDI
Chatter Zone
taksh 0 1829 Last post May 29, 2018, 02:41:52 AM
by taksh