|
Title: Naza M Lite Arming Issues Post by: RC4MIAN on July 24, 2021, 10:23:15 AM Naza M Lite build and setup done successfully but the issue is it arms in Manual Mode but does not arm in GPS and Attitude Modes.
Any inputs? Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 25, 2021, 08:55:50 PM what colour led flash are you getting while trying to arm in ATTI and GPS mode?
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 26, 2021, 10:10:23 PM Thank you for response Naveed!
Manual Mode - 3 red, gap, 3 red, gap, continues... Atti Mode - 3 red, gap, 1 org/greenish, 3 red, gap, 1 org/greenish, continues... GPS Mode - 3 red, gap, 1 green, 3 red, gap, 1 green, continues... Manual mode - it arms and motors response to controls Atti & GPS Mode - Motors run when holding the sticks in arm position and with letting go of sticks they stop. The run is also not smooth. Look forward to inputs. Thanks in advance! Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 26, 2021, 11:33:46 PM You're welcome!
I don't see anything wrong when you switch to the flight modes, the led colour codes are correct! After arming in either ATTI/GPS mode you need to increase your throttle to above 10% within 3 seconds of arming. If you don't do so the naza will automatically disarm. Refer to the DJI Naza M Lite manual Page 20 to Page 22, it discusses about various settings of the motor speed, motor cutoff and arming/disarming. what do you mean by the run is not smooth? Also i suggest you only fly in GPS mode, if no GPS lock then in ATTI mode! Manual mode is meant for pilots who do acrobatics and should never be used to fly normally. I use GPS and ATTI on one switch (3 way switch) and the failsafe on another switch (2 way switch). Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 27, 2021, 11:09:24 AM Yes, the LED seems to show right behavior for flight modes but the arming is not normal for ATT & GPS Mode.
The moment I leave the sticks to normal position the motors stop immediately, 3 seconds is too much of time in between! The speed of motors while holding the stick in arming position is not consistent either, there is a jerk in between. This is the case for both ATT & GPS modes. Any way forward? Yes, I try in ATT mode since Manual mode is a tough one. The set up of flight modes is done in similar to your description below. Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 27, 2021, 11:25:52 AM hmmm, Do a factory reset and do the whole setup process again the issue should be solved!
but note down your gain values and GPS position values before doing the factory reset Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 27, 2021, 01:41:03 PM Should I try upgrade to NazaM?
I saw some videos for upgrade or should I just reset it and try? Is it possible to connect with you on WhatsApp for quicker TAT? Thanks. Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 27, 2021, 01:43:38 PM I dont recommend upgrading the firmware M or M V2! if anything goes wrong your flight controller can get bricked.
So just reset it, there is an option for it on the DJI Assistant software Lets stick to the forum only as this will be a guide for other fellow hobbyist ! Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 27, 2021, 01:52:04 PM I tried the reset by following the F1 & F2 connect, connect to PC and power up but the screen remains unmoved as attached.
Any inputs? Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 27, 2021, 02:04:52 PM all you have to do is click on restore default, i used the Windows version
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 27, 2021, 02:27:21 PM I restored the default settings under tools and did the setup again but no change in result.
Could there be any other issue? Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 27, 2021, 02:28:44 PM Cant think of anything else, could you make a video showing the issue and share it
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 27, 2021, 03:47:17 PM I managed to create a video capturing the events but unable to upload here as attachment - any other way to share the video?
Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 27, 2021, 05:18:10 PM upload on youtube and share
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 27, 2021, 05:34:54 PM Please use the link:
https://drive.google.com/file/d/1xW5PJ87dZX5E6athUAC4Or-Gip6QZUdQ/view?usp=sharing Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 27, 2021, 05:47:32 PM This is indeed strange behaviour from the NAZA
Have you tried recalibrating each esc individually again? Other thing say you arm it in manual mode and then switch to ATTI/GPS mode does the thing still work? what brand ESC are you using? Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 27, 2021, 06:28:42 PM Yes, it is strange!
Yes, calibrated them all. If calibration is the issue then it would not be consistent even in Manual Mode I believe - right? After arming in Manual Mode if switched to any of the other modes the Motors stop abruptly. LittleBee 30A ESC are in use, will that be any issue? Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 27, 2021, 06:37:12 PM its not the ESC issue either!
not sure what the other issue is, cause i couldnt find anything else on it Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 27, 2021, 07:22:12 PM I am thinking of upgrading to NazaM version 4.02 and see as the last option, what do you say?
Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 28, 2021, 02:18:42 PM Upgrade to M V2, but do it on your own risk!
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 28, 2021, 02:33:06 PM Hmm, do we have a solution otherwise?
I have run out of options! From your response, it looks like a risky move. I will do some more search for a solution before the upgrade then! Thanks. Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 29, 2021, 03:19:18 PM What is your receiver brand and model ?
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 29, 2021, 03:22:12 PM I am using FrSky Tx - Taranis X9D Plus & Rx - RX8R
I also tried with FlySky Tx and Rx but no change in outcome Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 29, 2021, 03:24:42 PM Oh okay I was gonna suggest you try using the Sbus method to test out!
If two of your radios are giving the same result then it looks to be an issue with your FC itself Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 29, 2021, 03:27:51 PM I tried with S-Bus this morning, no change!
What should I do if the issue is with FC? Any tips? Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 29, 2021, 03:29:38 PM You could contact the seller you purchased from and tell them about the issue and see if they can replace it or contact DJI support and ask them for help.
Are you btw running the lastest firmware update on it? Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 29, 2021, 03:35:11 PM What is the latest version for it?
I guess the version 1.0 right? Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 29, 2021, 03:40:17 PM Yes V1.0 is the latest and the last update
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 29, 2021, 03:42:12 PM Again a road block!
Will give it some more time and see... Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 29, 2021, 03:46:15 PM Yup, whose video did you refer to while setting up the Naza and the taranis?
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 29, 2021, 05:45:32 PM I referred to multiple, do you have any best so that I can re-try, may be some luck I could hit!
Title: Re: Naza M Lite Arming Issues Post by: Mohammed Naveed on July 29, 2021, 08:28:26 PM i had followed Dennis Baldwin on youtube to set up my system
Title: Re: Naza M Lite Arming Issues Post by: RC4MIAN on July 29, 2021, 11:08:19 PM I too referred his for Taranis Setup!
|