RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: August 10, 2018, 05:24:23 PM »
Imperial fire
Plane Lover
Forum Hero

*****

Reputation Power: 11 
Imperial fire has no influence.
Offline Offline

City: Sangamner
State: Maharashtra
RC Skills: Intermediate
Posts: 662
Join Date: Feb, 2017

Keep calm and fly safe.




everything is working fine.
just need to get voltage reading on osd ( only voltage i dont care about current draw it needs to be callib too much anyways)

my 4 in 1 esc( yes it has a current sensor) has  a white signal wire meant to be connected to the f.c/
where do i connect it ?
i have currently connected it to the rx1 pad and assigned port 1 as esc sensor, but no use! ( marked with a green circle)
do i need to do any resource reallocation in cli ? if so whats the 'call sign' for current sensor?

or am i to connect it on some other pad?
yes i have enabled all settings in betaflight correctly i just need to know where to solder this!!!
thanks for your time and help!

rci.jpg
need wiring help for 4 in1 esc
* rci.jpg (67.18 KB, 738x502 - viewed 157 times.)
Logged
 

Read
« Reply #1 on: August 10, 2018, 05:26:19 PM »
Imperial fire
Plane Lover
Forum Hero

*****

Reputation Power: 11 
Imperial fire has no influence.
Offline Offline

City: Sangamner
State: Maharashtra
RC Skills: Intermediate
Posts: 662
Join Date: Feb, 2017

Keep calm and fly safe.



p,s yes all other osd settings work fine ... i mean timer and direction etc...
Logged
 

Read
« Reply #2 on: September 20, 2018, 08:20:59 AM »
kn8alpha
Plane Lover
Senior Member
***

Reputation Power: 2 
kn8alpha has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Advanced
Posts: 170
Join Date: Feb, 2016



Make sure you're using the right board/firmware on Betaflight, the voltage pins/scaling factors are setup by default.

Which board/ESC are you using?

The ESC outputs are usually VBAT (Lipo +), Motor1, Motor2, Motor3, Motor4, Curr, GND

I'm guessing the green wire is Curr output, which is a 0-3.3V signal from the current sense chip on the ESC board.
This wire is needed if you want current/mah data to the FC, connects to pad usually named as CURR.
Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
Need help with Airbus A380 wiring
Electric Planes
Doreng 4 5302 Last post May 18, 2011, 11:06:24 PM
by anwar
Multiplex Funcopter Wiring - Help
Helis
Doreng 4 4515 Last post September 08, 2012, 06:19:22 AM
by rcpilotacro
NEED HELP WITH FPV WIRING
Servos, Gyros and All Electronics
muradshak 9 7709 Last post August 02, 2013, 11:32:10 AM
by satyagupta
NAZE 32 and 12A ESC- wiring?
Multirotors
anilntny 5 3611 Last post January 01, 2016, 11:39:09 AM
by ilyas ali
FPV Wiring for Beginners
Servos, Gyros and All Electronics
Erpoyo 0 7555 Last post May 09, 2018, 02:41:53 PM
by Erpoyo