|
Title: help futaba r6106hf only two channels working Post by: romanxdsouza on March 07, 2013, 11:31:41 PM :help: :help: :help: i got a futaba transmitter t6ex and a r6106hf futaba recievers ,i want to set throttle on left stick and rudder and elev on right for my airplane just like in the picture 3channel, i have tried servos connected to all channels out of these only channel 5 and 1 work and channel 3works well for throttle, i have never used the other channels form the time i braught the rx and tx,im sure im going something wrong why are the other channels not wotking ,
have got a manual along it has information on the tx but rx it has info about r606fs and my rx is r6106hf so not sure if connections are same,someone please help hope im not bullied on the rx Title: Re: help futaba r6106hf only two channels working Post by: romanxdsouza on March 09, 2013, 12:16:37 AM guess all busy with sweep :giggle: :giggle: :giggle: :giggle: :giggle: :giggle: any way all works fine now thank u guys
Title: Re: help futaba r6106hf only two channels working Post by: sundaram on March 09, 2013, 07:41:39 AM Your receiver 6106hf is compatible with t6ex. Your question is not clear. Did you modify your tx For getting rudder on rightstick?
If not just connect rudder on channel 1 elevator on 2 and throttle on channel three. Ensure EPA and DR are 100% in all three. Title: Re: help futaba r6106hf only two channels working Post by: romanxdsouza on March 09, 2013, 02:15:43 PM thanks sundaram thts exactly wat i did connected rudder on channel 1 elevator on 2 and throttle on channel three so all good now just need to know if this diagram is correct i mean the channel numbers and the pins to connect servo
Title: Re: help futaba r6106hf only two channels working Post by: sundaram on March 09, 2013, 02:41:05 PM I do not have 6106. So I cant really help you with channel sequence. But it should be marked on rx I am sure. May be this will help you
Title: Re: help futaba r6106hf only two channels working Post by: romanxdsouza on March 09, 2013, 02:59:28 PM yes its the same which i have i dont knw about the pins behind i mean the for eg.. channel 3 and 1 are the pins in the middle behind as per the number on the rx so wich would be 2,4,6 then ,,its difficult to explain ...i understood numbers on the rx it is the 3pins behind wich connect servos im confused about
Title: Re: help futaba r6106hf only two channels working Post by: sundaram on March 09, 2013, 03:53:24 PM The centre pin is positive. The outer pins in all connecters where the notch is there is the signal wire white or orange. The inner pins of all connectors which is in center of the receiver is negetive or black
Title: Re: help futaba r6106hf only two channels working Post by: romanxdsouza on March 09, 2013, 08:59:03 PM sundaram sorry to be so confusing,the question mark on my diagram is the question,what is the channel num it is kind of difficult to explain so drew it hope this helps ,thanks for the diagram on the pins and connectors i got u ,dint know tht,
Title: Re: help futaba r6106hf only two channels working Post by: sundaram on March 09, 2013, 09:32:02 PM Unless you are not sure which mode your transmitter is you can just connect and identify the connector channel numbers ;).
however applying the same logic of R6004, the channel numbers should as at picture attached Title: Re: help futaba r6106hf only two channels working Post by: romanxdsouza on March 09, 2013, 10:10:01 PM hey thank u sooooo sooo much :hatsoff: :hatsoff: :hatsoff: i got it correct
Title: Re: help futaba r6106hf only two channels working Post by: sundaram on March 09, 2013, 10:30:41 PM you are most welcome :thumbsup:
Title: Re: help futaba r6106hf only two channels working Post by: romanxdsouza on April 08, 2013, 01:37:58 PM are these rates ok for my futaba tx for my blu baby as im a beginner dual rates 50% rudder and elev EPA-100%(with 50% epa the control surface hardly move) expo -30% rudder and elev Title: Re: help futaba r6106hf only two channels working Post by: sundaram on April 08, 2013, 02:54:04 PM Cant really say offhand like that. Depends on the surfaces and flying characteristics.
Title: Re: help futaba r6106hf only two channels working Post by: romanxdsouza on April 08, 2013, 06:10:55 PM got u thanks
|