RC India
Home Help Calendar Login Register
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: November 05, 2016, 05:26:22 PM »
joban13
Heli Lover
Senior Member
***

Reputation Power: 3 
joban13 has no influence.
Offline Offline

City: Chandigarh
State: Chandigarh
RC Skills: Advanced
Posts: 166
Join Date: Jul, 2015

The three connectors are seen after getting rid of the rubber glue on the connectors where antenna is soldered...  Now plz tell me where should i solder tbe signal and ground

Regards Joban
IMG-20161105-WA0013.jpg
Avionic receiver 6ch antenna broke, where to solder?
* IMG-20161105-WA0013.jpg (47.88 KB, 450x800 - viewed 401 times.)
Logged
 

Read
« Reply #1 on: November 05, 2016, 05:53:51 PM »
a3ruz
Plane Lover
Forum Veteran

****

Reputation Power: 1 
a3ruz has no influence.
Offline Offline

City: Kochin
State: Kerala
RC Skills: Advanced
Posts: 325
Join Date: Jul, 2015
Re:
Center pad is for the signal , the other two.pads are the ground
Logged
It's all about beging in air
CT6B | HK Bixler | APM | S550 | Tarot XYZ M | Turnigy 9x | Naza M V2 | Phantom 2 | Phantom 4 | Taranis X9D+ | F450 | ZMR250 | Naze | Omnibus | Martian II | Airypix | Airytek | Drone Racers Kerala
 

Read
« Reply #2 on: November 05, 2016, 06:46:44 PM »
arorasoham9
Plane Lover
Forum Veteran
****

Reputation Power: 5 
arorasoham9 has no influence.
Offline Offline

City: noida
State: Uttar Pradesh
RC Skills: Advanced
Posts: 320
Join Date: Mar, 2016
keep this in mind that u might Lose quite a bit of range in
doing this Repair job。。。its better to  buy a new receiver than to put your expensive crafts at risk
Logged
 

Read
« Reply #3 on: November 05, 2016, 07:04:15 PM »
K K Iyer
Global Moderator
Forum Hero
*****

Reputation Power: 61 
K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!K K Iyer is a rising star!
Offline Offline

City: Indore
State: Madhya Pradesh
RC Skills: Intermediate
Posts: 5180
Join Date: Jan, 2012
Quote from: arorasoham9 on November 05, 2016, 06:46:44 PM
keep this in mind that u might
Lose quite a bit of range in doing this Repair job。。。
its better to  buy a new receiver than to put your expensive crafts at risk

Is this a fact?
Or an opinion?

I soldered back the antenna on an FrSky 4ch rx (losing about 2mm in length)

Been using it for 2 years with no problem.
Currently in my 64" span Sunbird that is usually flown 3-4 times as far away as a typical foamie.
Logged
 

Read
« Reply #4 on: November 05, 2016, 08:58:29 PM »
Swapnil
Plane Lover
Forum Hero

*****

Reputation Power: 20 
Swapnil barely matters.Swapnil barely matters.
Offline Offline

City: Pune
State: Maharashtra
RC Skills: Beginner
Posts: 1755
Join Date: May, 2010

Retreat, Hell!
@joban13

Do a range check after soldering.

Sometimes the signal wire can break at the point(s) of impact. So, do a continuity test as well just to be safe.
Logged
 

Read
« Reply #5 on: November 05, 2016, 09:01:43 PM »
saikat
Plane Lover
Forum Hero
*****

Reputation Power: 14 
saikat has no influence.
Offline Offline

City: Tezpur
State: Tripura
RC Skills: Expert
Posts: 1130
Join Date: Jul, 2009
good one K.K.

only the unshielded part is what matters - should be about 30-31mm for 2.4ghz


so yes you can solder the broken antenna back on with no ill effects (generally speaking)

Swapnil has summed up rather neatly.
Logged
https://t.me/pump_upp
 

Read
« Reply #6 on: November 24, 2016, 11:40:21 PM »
Dharmik
Heli Lover
Forum Hero

*****

Reputation Power: 13 
Dharmik has no influence.
Offline Offline

City: Bharuch
State: Gujarat
RC Skills: Beginner
Posts: 1097
Join Date: Sep, 2011
please check the topic i just posted. it might help you repair your rx
http://www.rcindia.org/radios-and-receivers/receiver-antenna-repairreplacement-guide/msg265068/#new
Logged
 

Pages: [1]   Go Up
RC India  RC Equipments  Radios and Receivers  Topic: Avionic receiver 6ch antenna broke, where to solder?
« previous next »
Jump to:  

Related Topics
Subject Started by Replies Views Last post
Need Hobbyking receiver extension antenna
Wanted 		hangingtough 0 1715 Last post January 11, 2012, 10:18:06 PM
by hangingtough
2.4 Ghz Receiver Antenna
Radios and Receivers 		Mjet 10 6527 Last post January 31, 2013, 12:00:38 AM
by sundaram
Need of a receiver antenna
Wanted 		arun.sreelakam 2 1956 Last post April 28, 2013, 07:22:54 PM
by arun.sreelakam
receiver antenna
Wanted 		kiran rc 4 2429 Last post January 24, 2014, 03:39:47 PM
by kiran rc
Lead solder (Solder with lead greater than 40%) availability
Tools, Materials and Building Techniques 		veloci 9 6150 Last post February 01, 2016, 07:56:45 PM
by lastRites
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
Simple Audio Video Embedder 		Realized by Systalent | XHTML | CSS