RC India

Guys ive got a HK T6a v2 transmitter which is presently in some problem because the antenna wire in the tx that gets soldered onto the radio board is disconnected , i dont know which wire should be soldered where
the antenna has 2 wires, please help me on how solder and where , please,  :help:  :hatsoff:

anyone who has a hk/flysky t6a or t4a  transmitter please open ur tx and upload the pics of the radio board along with the antenna wire , so that i can see which one goes where

hey its simple the inner wire with shield goes to center node! and outer wire without shield or tinned goes either of the two outer patches or node !
hope this helps!

but the connection is not there between the chip(white one near the 3 terminals) is broken so should i connect the chip and the centre terminal with a wire first

Daksha..at first do not panic..and, yes the science of  Electronics is not a monopoly to anyone..anyone interested can follow Electronics and can do ample of things..for that we do not need to study the deepest theories..a person with a deep theory knowledge in Electronics never do practical stuffs..so, once again, do not worry..you can also do many things in Electronics..here you facing a simple problem..antenna of your Tx is broken..ok..

the most of the presntly available radio sets are produced in a same mother factory in China..in various brand names..these radios ranges from 4 to 9 channels..so, most of the components are same..here you can see the same transmission unit..
     At first, take your antenna module, so, you can see a gray wire, more clearly a shielded wire, with one core and one shield..slowly, remove the stiff plastic sheeth, from tip, to reveal the wires..wrap, the shielded wire gently, all along..strip a little plastic sheeth from inner wire..now we have two wires in hand, with antenna module..
now take your PCB in hand..and you can clearly see here , about the terminals as i marked..
for more clarity, i removed the antenna for you..its clear..

now, you can connect any broken link by soldering it..for that you do not need any SMD station..instead take a piece of copper, or brass wire, some thick, and clean its one tip with blade, or by art knife..

wrap it on the tip of the existing soldering iron..as shown..

now you can solder it easily..and never forget to pull out the plug of the soldering iron from wall socket just before soldering..because a leakage current from your iron can damage some internal parts of the radio unit instantly..checkout all connections are sound after solder..take some extra care while soldering..patience is sucess..its all simple.. :thumbsup:

sir that is so kind of u to do so much work just to show me  {:)} {:)}  :hatsoff: :hatsoff:
but actually maybe my radio board can never be fixed because , a week ago , i had tried to solder , but by mistake i had dropped a drop of hot lead on that white chip (IC)  :banghead: :banghead: :banghead: ,so the lead was not coming out at all, and after seeing your guidelines i tried again , but the tx didnt bind with the rx at all   :'( :'( :'(
maybe my bad luck ,and sounds like i have to get a new radio.
Thanks for ur help sir :hatsoff:

and sir now that my radio board is gone , can i use the turnigy 9x module ,and moreover the turnigy 9x module binds with the hk t6a v2 reciever, so can i swap the present module with the turnigy 9x one

Daksha..i wonder that, actually i do not know, why you disconnected the antenna from main board..any way, i hope you may damaged the transmission unit once..and most of such radios are in same coding and can try with all others..and i will try once that to get a transmitter board for you from Fly sky..i hold one now, but it is intended for my coming model project..so, once again, by using a lens, please trace all tracks, for any short circuits and openings.. :thumbsup:

Sir about a month ago both tx and rx were working fine, but 1 day i did a glide test for my plane, so on crash landing , the reciever went , but i thought the transmitter went , so went to rcgroups and noticed one guy saying that there may sometime be a problem due to the disconnection of the wire going from the main board to radio board, so i went , stripped my tx and cross checked the wires going from main board to rx board , no defects in the wires , as i was fiddling , the antenna wire snapped
 :banghead:  :banghead: , then somehow wrongly soldered it back on and bought another rx from vineet , when i got it that too didnt work , so then i created this thread ;D