RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: May 13, 2016, 03:52:54 PM »
Rathi
Plane Lover
Senior Member
***

Reputation Power: 2 
Rathi has no influence.
Offline Offline

City: Banglore
State: Karnataka
RC Skills: Intermediate
Posts: 166
Join Date: Feb, 2016




i wanted to know how i could use S-bus on the RCB OS-10 sbus compatible reciver. there are no online vids nor are there any manuals on it. I am running mac os and i do not have option for their software as it is not available for mac. Undecided
appriciate the help  Grin Grin
Logged

Bolt 210
QJreaper 6"
taranis 9XD+
its either FPV or nothing.
 

Read
« Reply #1 on: May 13, 2016, 08:39:23 PM »
RcBazaar
Heli Lover
Forum Hero

*****

Reputation Power: 9 
RcBazaar has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Advanced
Posts: 664
Join Date: Jan, 2011



hello Rathi
the process of usage is as below
1. Remove all power input to the RX
2. TX is switched ON (of course the TX and RX needs to be bound to each other earlier)
3. Press the Bind button on the RX and give power supply to the RX when the LED switched ON then release the button. Now channel 10 will output the SBUS in PWM signal
The next process is similar to any futaba sbus system of setting up with your sbus servos...

regards
Sujju
Logged

 

Read
« Reply #2 on: June 20, 2016, 12:09:04 AM »
Swapnil
Plane Lover
Forum Hero

*****

Reputation Power: 20 
Swapnil barely matters.Swapnil barely matters.
Offline Offline

City: Pune
State: Maharashtra
RC Skills: Beginner
Posts: 1755
Join Date: May, 2010

Retreat, Hell!



Sujju sir,

Is the process similar for PPM mode?
Logged
 

Read
« Reply #3 on: November 18, 2017, 09:24:49 AM »
Comet
Heli Lover
Active Member
**

Reputation Power: 1 
Comet has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Beginner
Posts: 20
Join Date: Mar, 2017



Sorry, for reviving such an old thread but I need to connect the 10Ch receiver to Pixhawk 2.4.8 and need to configure it either in SBUS or CPPM mode only. I would like to request a step by step tutorial with some pictures of the pins if possible.
Logged
 

Read
« Reply #4 on: November 18, 2017, 10:34:46 AM »
Swapnil
Plane Lover
Forum Hero

*****

Reputation Power: 20 
Swapnil barely matters.Swapnil barely matters.
Offline Offline

City: Pune
State: Maharashtra
RC Skills: Beginner
Posts: 1755
Join Date: May, 2010

Retreat, Hell!



@Comet
I tried a lot but wasn't able to figure it out. Hope someone from RCB helps us out.
Logged
 

Read
« Reply #5 on: November 18, 2017, 11:39:39 PM »
Comet
Heli Lover
Active Member
**

Reputation Power: 1 
Comet has no influence.
Offline Offline

City: Bengaluru
State: Karnataka
RC Skills: Beginner
Posts: 20
Join Date: Mar, 2017



I figured it out. It's exactly as per the instructions. I will post the procedure with some pics tomorrow.
Logged
 

Read
« Reply #6 on: November 19, 2017, 10:54:04 AM »
rishabhbarma
Plane Lover
Forum Hero
*****

Reputation Power: 13 
rishabhbarma has no influence.
Offline Offline

City: Kolkata
State: West Bengal
RC Skills: Intermediate
Posts: 921
Join Date: Mar, 2015



Process to use sbus-
Remove battery from avionic radio.
Trash the radio.
Buy a flysky(really low budget)/ qx7(low budget)/ X9D (mid budget.)

P.S. jokes aside the avionic radios are quite trashy, you should upgrade asap
Logged
 

Read
« Reply #7 on: May 16, 2020, 06:52:43 PM »
jangoachayan
Plane Lover
Active Member
**

Reputation Power: 1 
jangoachayan has no influence.
Offline Offline

City: Kannur
State: Kerala
RC Skills: Beginner
Posts: 4
Join Date: May, 2020



You just need a ppm encoder. Connect the receiver channels to the input of ppm encoder and the output to the first pin of the pixhawk RCIN (NOT SBUS).
Logged
 

Read
« Reply #8 on: May 27, 2020, 09:04:50 AM »
jangoachayan
Plane Lover
Active Member
**

Reputation Power: 1 
jangoachayan has no influence.
Offline Offline

City: Kannur
State: Kerala
RC Skills: Beginner
Posts: 4
Join Date: May, 2020



Might be a late reply but may still help people like me who struggled for quite some time on this

the procedure is as follows

1. Bind the receiver to transmitter normally ( if not already bound )
2. Disconnect receiver power
3. Press the bind button while not powered on and then connect to power keeping the bind button pressed
4. A blue light should illuminate indicating receiver in SBUS mode

Note
To connect to pixhawk connect channel 10 of receiver marked SBUS with the channel on the pixhawk marked PPM (first pin on the left). If you connect to the one marked SBUS it wont work because that is  SBUS output

Hope this helps.

a method showing this method is explained for their 8 channel Avionic RZ8 receiver it works for the 10 channel receiver as well
Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
Wanted : Sbus signal inverter
Wanted
devangflyer 0 1247 Last post August 28, 2014, 01:12:17 AM
by devangflyer
Futaba SBUS compatible Tx Rx
Wanted
mohitgurjar 0 1063 Last post September 29, 2015, 07:51:16 PM
by mohitgurjar
Flip32 and SBUS Config
Multirotors
arunlouie 5 4529 Last post June 14, 2016, 06:00:47 PM
by arunlouie
FRSKY SBUS RECEiver for SALE
For Sale
ad! 4 1955 Last post March 24, 2017, 05:14:40 PM
by ad!
For Sale: FlySky i6s ( touchscreen ) with phone stand and 10 CH reciever ( sbus)
For Sale
adit3094 1 1768 Last post September 21, 2017, 10:16:17 AM
by adit3094