|
Title: servos not reacting in spite binding ..... plz help Post by: sameermaha on December 08, 2012, 06:19:50 PM i got my turnigy tode......
i am able to bind to reciever..... but servos are not reacting...... plz help..... :help: :help: :help: binding is fine...... steady light present..... i have also tried making all default factory settings..... plzplzplz help Title: Re: servos not reacting in spite binding ..... plz help Post by: rajathv8 on December 08, 2012, 07:14:33 PM Which channels are the servos connected to ?
Is the ESC connected to the throttle channel? To which channel did you connect the bind plug while binding? Title: Re: servos not reacting in spite binding ..... plz help Post by: sameermaha on December 08, 2012, 07:27:16 PM i haver connected servos to ch 1234 and esc to battery..... channel 10
bind plug to 9ch Title: Re: servos not reacting in spite binding ..... plz help Post by: sameermaha on December 08, 2012, 07:31:45 PM is there some problem with soldering of these chinese radio?? my freind suggested it might have loose soldering...... shud i open it and see?
Title: Re: servos not reacting in spite binding ..... plz help Post by: lastRites on December 09, 2012, 06:12:02 AM Did you not remove the bind plug before connecting the servos?
Title: Re: servos not reacting in spite binding ..... plz help Post by: saikat on December 09, 2012, 08:48:44 AM check the polarity of the connection - take out the plugs and plug in "ulta" to what you
have been doing - the white / orange wire should be on top and black/brown wire bottom Title: Re: servos not reacting in spite binding ..... plz help Post by: rajathv8 on December 09, 2012, 11:16:41 AM The bind plug must be connected as below:
"It is actually quite straight forward provided you realize that during the bindi9ng process the bind plug goes into the battery socket while the battery goes into the socket labeled bind. The bind button on the transmitter module is labeled the bind range test button. Good luck." Picked up from: http://www.hobbyking.com/hobbyking/forum/forum_posts.asp?TID=13890 (http://www.hobbyking.com/hobbyking/forum/forum_posts.asp?TID=13890) Once this is done remove the bind plug. :) Title: Re: servos not reacting in spite binding ..... plz help Post by: sameermaha on December 09, 2012, 11:35:51 AM after i remove bind plug... to add a servo...... sud the binding light go off??
Title: Re: servos not reacting in spite binding ..... plz help Post by: sameermaha on December 09, 2012, 11:45:20 AM binding is fine
after red ligt is steady...... i turn off tx rx .... remove bind plug ...... plug servo... put power on for tx rx...... nothing moves....... red light doesnt glow without bind plug ...... is it normal??? :headscratch: :headscratch: ??? ??? Title: Re: servos not reacting in spite binding ..... plz help Post by: Hellyflyer on December 09, 2012, 12:00:56 PM Have you changed the polarity as mentioned by saikat above? Cause that's what's going to resolve your issue here
Title: Re: servos not reacting in spite binding ..... plz help Post by: lastRites on December 09, 2012, 12:37:04 PM Are you only plugging in your servos and not your esc? Its the BEC of your esc that supplies all the power..
Title: Re: servos not reacting in spite binding ..... plz help Post by: sameermaha on December 09, 2012, 02:18:29 PM IT WORKED!!!
i m so happy... thks guys..... i ws making combined mistakes..... bind plug not removed.... and the polarity change.... ulta trick worked thks again... |