RC India

Hi to all Turnigy 9x user,
Please confirm the following:
When going for Flaperon function:

FLAPERON
STATE         INH
AIL1            000   000
AIL2            000   000
When changing to INH  the options 000 000 in both AIL1 and AIL2 is fluctuating.
Please confirm all turnigy user whether the same thing is happening with you also?
Sandeep

i m planning to buy this Radio, is it not worthy enough, pls suggest ...

Muzammil.

Nooooooooooooo...
don't cancel your plan to purchase...my problem was minute and was solved..i would suggest you should go this tx.

Sandeep

Hello Sandeep,

Thanks for ur prompt reply but as i see the comments at hobbyking website most of the users of this radio has one or another problem http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=8992

please have a look, also suggest me a good radio under 6000 INR

Thnks in advance :)

Muzammil.

Hi Muzammil,
see the thing is that the reviews is ok there, but read some more reviews on other location and suggested by user of the forum only i.e. Saurabh. even i took his words about good review of radio and sold my Futaba radio just to purchase turnigy. i have flown my pilatus on this new radio and didn't find any difficulty. one more user from Panvel-Mumbai is also using the same radio for all his models. he is also having an online store for R/C product. if you want more stability on this radio, simply remove original module and put Frsky module for fail safe function . if your budget is 6k, then this is best option as new or you can put a wanted request for Futaba second hand radio, but that is for sure that you will not get 2.4 Ghz in Futaba in 6K. rest is your luck...
Sandeep

Hello Sandeep,

Thanks again, i m convinced with the Turnigy Radio now but the real problem is now its not available newhere, i tried Hk as well all Indian online stores, but everyone is saying that they have ordered it & wil reach within 15 days, could u tell me where did u get urs, Also where to get Frsky Module & how much does it cost, i saw a video on Youtube where we need to open the Turnigy Radio in order to solder the Frsky Module inside the Turnigy Radio, is this the only way to do it, pls clarify...

Thanks Buddy...

Regards,

Muzammil

Hey just saw this on Rcbazaar.com
http://www.rcbazaar.com/products/397-fs-th9x-9ch-24ghz-transmitter-receiver.aspx

is this the same Turnigy 9x u r using pls confirm....

Yes Sunny,
It is the same radio, but I am not sure if the firmware is the same. This radio is basically designed for open source code. There are various firmware available on the net for this radio. I have the Turnigy one and it so far is good and reliable. I even fly my EPP FPV with autopilot on this radio. For the FrSky module, you can either use the DIY kit or the JR compatible FrSky module. But anyway you will have to open the radio to remove the stock module.

Here is the module : http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=14355

Here is the DIY : http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=14353

Good Luck.

Hi sunny_16977

The hardware is the same but the software is a bit different from one available from rcbazaar,

Radio is built around AVR micro controllers and folks at rcbazaar are working out a new firmware based on ER9X, once programmed the radio's firmware will be at par with high end radio's

hi
i bought this radio a few months back from jack hobbies.
i have added a blue led backlight system and it looks pretty cool.

Thanks Saurabh, Jatayu & Vishal for ur Replies, i m not so well versed with modifications, should i buy SANWA/AIRTRONICS SD6-G 2.4Ghz W/6CH RX, from Rcdhamaka which cost 7.8K,
 http://www.rcdhamaka.com/index.php?main_page=product_info&cPath=89&products_id=703
i m not sure whether it supports Fail safe, do tell me guys which is good for me, as i m in to Helis at the moment, wil also wants to use it as a simulator as i m a Beginner.

Thanks once again,

Muzammil.

forget the modifications, thats just an experiment. between turnigy and sanwa, sanwa is definitely the better one. i just got the sanwa sd 10 g from rcdhamaka. 

Vishal i saw Sanwa 10 g at rcdhamaka its awesome man

Hi everyone.
Can anyone help me in setting up turnigy 9x for simulator, I have downloaded both ppjoy and vjoy
But could not make heads or tail out of it also which cable to be use and at which computer port,
I tried the Normal stereo cable is it ok.
Please help me out.

Subir

Hello Subir,

Just bought my Turnigy 9x from Sujit, i m following the instructions from here http://www.hobbyking.com/hobbyking/forum/forum_posts.asp?TID=1428

u try it too, let me know if u get thru.

Regards,

Muzammil.

Hi Subir,

I m able to use my Turnigy 9x with Leo's RC Simulator as of now, the catch to make it working is to remove the module from the radio's back, i m using 3.5mm jack on both ends, do let me know if u have any problems, wil have to try to make it work with Real Flight/Aero Fly/XTR/Phoenix.

Wish me Luck :)


Hey its working Beautifully with FMS  {:)}

hi,

I need to know is there any other hk receiver compatible with the Turnigy 9x transmitter.

anybody using a different brand other than the one which comes with 9x.

regds

Hi sunny

Do you need to take out the transmiter module for the fms also.

Subir

Dear Sbajare,

Rcbazaar has Flysky 8ch & 6 Ch receivers which r compatible with Turnigy 9x, i have ordered 2 for myself. (yet not Tested)

Dear Subir,
i have taken out the Module & i m using various simulators which i have ordered from rcbazaar, i m using 6 in1 USB simulator package, so never tried poping the module in & out, i wld suggest u to remove the module always when using any simulator, thats how it works for me...

 

Hi Subir,

Yes, you have take module out as sunny suggested, for FMS as well.
I'm also using Turnigy 9x with FMS it's working fine for me. Also you will notice it saves lots of battery when you take module out and use it for simulator.

Please calibrate it with FMS before using.


Thanks,
-Vinayak.

how do you disconnect the antenna

Subir

No need to disconnect the antenna.

Just pop out the module and that’s it. It will keep hanging with antenna wire.  And thats it. You should be ready to use it with simulator. That’s how I use it with FMS.

As the module will be hanging out with antenna wire you have to take precaution while using it. You may stick it somewhere else with double tape, or put piece of thermocol in hatch of the module so that connectors of module will remain disconnected.

I bought my Turngy 9x some time back with 2 Rx.
Once the RX is bound to the TX is there a process to debind the Rx from the TX. I need this because at any given point I want to use only one Rx.
I intend to use this radio  on my boat and rescue boat. Now assuming that my primary boat is stuck in middle of a lake and I need to send my rescue boat to get it back, and I have only this radio, I do not want the primary boat rx to respond to any functions when the rescue boat is operating since it will defeat the entire rescue operation .

Help!!!

Shreekant

Guys, anyone using turnigy after changing  frsky (the kit which directly solders)
Will the simulator work without any mods  after changing to frsky ???

Help Help!!!!!

Yes. I have been using the Turnigy 9X + FrSky DIY for a long time now. No probs with simulator. It works as good. No mods for sim required.

Hi,

http://rcbazaar.com/products/397-fs-th9x-9ch-24ghz-transmitter-receiver.aspx (http://rcbazaar.com/products/397-fs-th9x-9ch-24ghz-transmitter-receiver.aspx)
I have seen FS -TH 9x tX in Rc bazaar site.can someone tell whether this tx is gud one to buy and what is the difference between turnigy and FS -9 channel.Actually i am looking for Turnigy tx, but i dont find it in indian stores.
Please give ur opinion on this FS -TH9x ?

thanks,
krian

Hello Kiran,

I m using Turnigy 9x which is similar to Flysky 9x, Copterx CX- CT9A, Imax 9x, they are all the same with just different brand names, rcbazaar has got the same Tx which is as good as Turnigy 9x.

There is a yahoo group dedicated to Flysky 9x, chk here : http://groups.yahoo.com/group/Flysky_RC_radio/


Regards,

Muzammil.

i bought the FS-th9x from rcbazaar, thanks for ur advice.

Dear sreekanth,
i am using the Hobby king TX and RX but it is exactly the same as this one. The process of binding the second rx will unbind the first RX. So your purpose is solved

u r welcome kiran

@Hangintough... No this does not solve the problem. Even if the second RX is bound to the TX the first RX also accepts the signals. It does not get unbound ( not sure if this is correct word)

Shreekant

@kiranch19
Can you please tell the range that you are getting for TH-9X ?

Dear rooster,
You are not correct, when you bind the second RX , the first RX will get auto disconnected.

The Turnigy 9x has model memory so all you need to do is bind both the RX at differnt memory locations and then change the location on the TX .

Hellyflyer

Guys, I recently added rudders for f22 and am facing problem with prog mix.
Following is the setup.
Right servo is going to channel 6
Left servo is going to channel is 4

AUX-CH menu set to GEAR ( to enable it)
Prog.Mix Menu
Mix1
STATE          ACT
MASTER       RUD
SLAVE         FLP
OFFSET       000
UPRATE       100
DOWNRATE 100
SW             ON


Problem i am facing
Moving rudder stick to the right: Both rudders are moving to the right together (this is fine)
Moving rudder stick to the left: Left rudder moves completely to the left, right rudder is in neutral position.

Is there any configuration i need to add??