This is the review of most Hyped Radio of the year Turnigy 9XR-

Saurab Srivastava and I, got it almost together (Some pics are courtesy Saurab).

Some Pluses

Good feel to it,
Neat Handle
Good Bright Display
Cheap

Where is the review............?

Orange LR modules fitted well, rx  binding and connection was no issue, will fly fpv and let you all know further. side by side with 9X, 9XR is shade smaller and lighter (With the module)

Some Minuses

Menu key is sticky

Switches feel cheap

balancer wont fit with tx batt having shorter balancer
with the antenne connected to the module, you wont be able to keep the Tx down, solution is to connect it to the internal antenne, then you wont be able to change the module as often as i intend doing

Too bright a display for night flying

Standard tx stand wont fit, need to diy, then the ergo is lost

Has both the trainer ports,
A word about the case, case is good looking but has some play at the hinge and feels slightly cheaper and not as good as it looks.
hooking up to the PC, will report back on the software issues if any and flying reviews with FRSky, 9X, Orange LRS and Spektrum modules

PS
People who have it are welcome to participate. Who dont watch out this space

has been split to accomodate pics along with the review.  . you were quick to draw  >

One could argue if module is included 9X is cheaper, but then you get good gimbals and next gen radio. ideal for FPV fliers, you could hook up your LR module for FPV and change over to normal module for other close vicinity flying

Menu key sucks..though unlike 9x it makes less noise while hitting a key,most of the time I have to press really hard to get any response..

Aww...sir.That case and that side looks so sexy!Be a little less harsh on the radio sir.afterall u save almost 150$ for same features on a futaba!

indeed 

switches are placed at an angle which will require some getting used to, i would advice some mock blind folded reach of the switches before assisgning and flying with them

How much in total did u pay for it
?

103 $ (75$+28$) for the Tx and the case (Shipping Incl)

here is the user manual

here are some general features taken from the website

9XR Standard Features:
• 8 Channel PPM/9 Channel PCM
• Full Ball Bearing gimbals
• Adjustable Stick Length
• Digital Trims on all Primary Axis
• 16 Model Memory
• Assignable Switches
• Freely Assignable Channel Mixes
• Graphical Dual Rate and Exponential
• Sub Trim and Travel Adjust
• Flaps and Differential
• Throttle Hold
• Supports Heli/ Aero/ Glider Model Types
• Programming Templates Based on Model Type
• Supports M1, M2, M3, M4 stick modes
• 128 x 64 backlit Liquid Crystal Display
• Built in JR & Futaba Trainer Ports
• PPM & PCM Output
• JR Form Factor RF Modules (Orx Dsm2, Orx Open LRS 433Mhz etc)
• Programmable Timers
• Low Voltage Warning and Buzzer
• Supports 3s Lipo (Required)
• 9XR Firmware Pre-loaded
• AVR ISP Interface
• Internal 2.4GHz Antenna

Have you got the receiver with the orange module ? or you have brought separately.

Bought them seperately

Has the 9xr team made any significant changes to the er9x firmware...

 here is the LR EPP FPV flown with 9XR with the LRS module, batt is holding out well, next module to go in will be Spektrum Orange, will report back with the same, soon

here is the thread

and the pic

My 9xR works great with the Fly sky 9ch 2.4 Ghz module
+1 for 9xR. It feels great when you hold a 9xR compared to a turnigy 9x.

Me too love the looks... 

Haha yup. Which one do you have?

The basic flysky 6ch one(my first)... 

Nice. But it dosnt matter. You are pro enough to make this radio turn better than a 9xR

Haaha i am a big big beginner(didnt find any lower positions to select in this forum) 

Just a word of caution that Mode changes are tricky in 9XR. I bought a mode 1 as that was available at the time thinking it is easy to change to mode 2.
I landed up eventually cutting cables and soldering wires to finally get everything working. I changed then two gimbals.

My advice would be buy the one which you fly with. 9x on the other hand was easy.

Cheers
Asutosh

9xr mode change is fiddly and involved but not difficult.
I've done it without any hassles.

The gimbals are not full ball bearing i.e only one end of each axis
is supported by a ball bearing.

I'm using mine with a frsky JR module - works well enough.

I find the firmware weird and am planning to flash to the original
9x v2 firmware.

Otherwise - it an okay tx - but I find the 9x has a better feel.

I want to charge the lipo thru the charging jack - any suggestions
on how to do this ?

Please no dire warnings - I'm well aware of the  purported risks
involved.

I was planning to connect the balancer tap to the futaba training
port - and use a custom wiring harness , for charging and
balancing the battery while in  the tx.

Any flaws in the above ?

@saikat, sounds perfectly ok if you can bring out the taps, cant say specifically on the the 9xr (dont have one) but for the 9x I've got a similar setup.  Rarely do I charge the battery outside the Tx, only when I have to physically inspect. The pos neg go to the 12v jack in the correct polarity and the taps go to the balancer port on the charger

didn't expect they'd make the mode change so convoluted.

PS: er9x is like arranged marriage. confusing at the start but then you start enjoying it Don't know if that goes for love marriage too, mine was arranged

Flashed with old 9x v2 firmware

how to get the backlight working ?

anybody ?