|
Title: urgent pls help with my transmitter Post by: khan007 on February 21, 2014, 10:28:03 AM friends i was making a new plane .its my first plane .i set up esc and servos .i gust checked for range with my flysky t6 tx .i got no range above 5m .i dont know whats the problem pls help
Title: Re: Post by: docnayeem on February 21, 2014, 10:51:11 AM Are you doing the range test with bind button pressed ?
Title: Re: urgent pls help with my transmitter Post by: khan007 on February 21, 2014, 11:44:30 AM no
Title: Re: urgent pls help with my transmitter Post by: khan007 on February 21, 2014, 12:15:19 PM do i need to repair any thing
Title: Re: urgent pls help with my transmitter Post by: SideWinder on February 21, 2014, 02:22:07 PM Are the batteries fully charged? How are you powering the Tx?
Did you ever try to power the Tx without the antenna if its removable? Title: Re: urgent pls help with my transmitter Post by: v2 eagle on February 21, 2014, 05:01:54 PM Pics and videos of setup if possible, i can help you.
BTW i have the same radio and i can fly more than my eyes can see. You must be doing something terribly wrong in basics. Ashok.P Title: Re: urgent pls help with my transmitter Post by: utkarshg13 on February 21, 2014, 06:44:51 PM I think you must have not followed the binding procedure properly... Try binding it again using manual given... or the TX must be on under power battery or something. One photo of the setup would be helpful. I too use a Flysky T6 tx and had no such problem till now.
Also, did you disconnected the bind plug from receiver after binding it... :giggle: :giggle: I usually forget to do so... ;) Title: Re: urgent pls help with my transmitter Post by: rcpilotacro on February 22, 2014, 10:25:26 AM Your antennae is most probably broken
Title: Re: urgent pls help with my transmitter Post by: khan007 on February 22, 2014, 01:41:05 PM how to find which side ?on the rx or on the tx?anyone pls help i am stranted
Title: Re: urgent pls help with my transmitter Post by: utkarshg13 on February 22, 2014, 06:58:25 PM It seems the antenna wire at receiver must be broken. Broken connection inside.
Title: Re: urgent pls help with my transmitter Post by: khan007 on February 22, 2014, 08:31:26 PM guys latest update .inside the available range .i covered the rx antenna -by holding hand- and then i lost the signal.then i tried covered tx antenna with out covering rx antenna.then there was no loss of signal.i assume that the problem is with tx antenna .whats ur opinion?
Title: pls help with my flyskyt6 Post by: khan007 on February 25, 2014, 01:43:33 PM friends i need help with my flysky t6.so pls pm me who have it?i need ur help
Title: Re: urgent pls help with my transmitter Post by: anwar on February 25, 2014, 01:50:55 PM What exactly is your problem ? You are opening new topics on transmitter issues without saying what the problem is !
Please stick to one thread on one issue. Try it, it is not that difficult ! Title: Re: urgent pls help with my transmitter Post by: khan007 on February 25, 2014, 06:24:10 PM oky
Title: antenna making help needed for rc receiver Post by: khan007 on February 27, 2014, 01:00:24 AM friends .my rx antenna look like ugly.its the flysky r6b rx.it got reduced range.while inspecting.i found the shield solder is not good.if i need to resolder it ,i will need to cut it.so i gonna need a new antenna?(does reducing the antenna wire length affect the range?) i need ur advice pls help .i googled it .but i cant find right answer(the antenna which i have contained a tube like part on outside. Those antennas on other sites doesnt have that).thats why i need ur help?
Title: Re: antenna making help needed for rc receiver Post by: utkarshg13 on February 27, 2014, 09:34:25 AM See, my antenna wire broke and came out. I'd cut a small part of it almost 5mm and then resoldered it. No range issues till now. works finely.
Title: Re: antenna making help needed for rc receiver Post by: KALYANPRODHAN on February 27, 2014, 04:24:10 PM Surely either antenna connection itself (central wire of co-axial) or shielding wire is disconnected.
You have to cut it at very small and have to solder it. Use 6-10 watt soldering iron with very sharp tip to avoid shorting between tracks. Title: Re: urgent pls help with my transmitter Post by: khan007 on February 28, 2014, 11:36:47 AM friends i findout the problem was with my tx antenna .i need to change the antenna,does the normal wifi antennas work with it? Does this antenna work (link below)? I need ur feed back pls help.
http://www.youtube.com/watch?v=bs8hvXGJdhM#ws (http://www.youtube.com/watch?v=bs8hvXGJdhM#ws) Title: Re: urgent pls help with my transmitter Post by: khan007 on February 28, 2014, 01:55:20 PM anyone?
Title: Re: urgent pls help with my transmitter Post by: Hellyflyer on February 28, 2014, 02:34:21 PM The antenna in the video will not work.
Title: Re: urgent pls help with my transmitter Post by: khan007 on February 28, 2014, 02:57:34 PM why?
Title: Re: urgent pls help with my transmitter Post by: v2 eagle on February 28, 2014, 03:04:25 PM What is actually wrong with your antenna?
how come you found that the antenna is the problem, well if your TX antenna is damaged and you used the TX along with it, chances are that you can damage your module itself. however any WIFI antenna from ebay.in can work with it but it should have a screw type connector for it. Ashok.P Title: Re: urgent pls help with my transmitter Post by: khan007 on February 28, 2014, 03:11:56 PM i already soldered the sma connector only need to connect the antenna
Title: Re: urgent pls help with my transmitter Post by: khan007 on March 01, 2014, 05:22:06 PM anyone got any idea?
Title: Re: antenna making help needed for rc receiver Post by: khan007 on March 01, 2014, 05:25:43 PM oky
|