Kingkong force 200 is a quadcopter kit but I am confused where to buy it as on banggood it costs me around 3700 ( with discount) but on rees52 it costs me 5000 so please give suggestion and help me out .
And please inform me if you have better site or kit .






Regards

These are good for a beginner the motor takes a few crashes well   , but try getting the 20a esc kit .. 

Thanks for the suggestion
And I will go for them
Kingkong force 250

I need one more help from where to buy

Go with banggood, i have ordered many times from them and never had any issue. Keep in mind that it may get seized by customs, if the box is big which may catch custom's eyes. Ask banggood to name the package as 'tools' or 'hardware'.

This is the reason i do not buy whole kits, i buy seperate parts and build it.

Can you give me your budget, i can then suggest you some better parts than that kingkong build.

Thanks for your helpful reply
Actually by budget is around 4000 to 5000
 
# tushar

If you can push upto 6000, you will get an awesome build for racing.
Here are the parts list:
motors- racerstar br2205S 2600kv  price-
1970rs
 https://www.banggood.com/4X-Racerstar-Racing-Edition-2205S-BR2205S-2600KV-2-4S-Brushless-Motor-For-210-QAV250-280-FPV-Frame-p-1101510.html?p=AL24049130595201702U


Esc-4x racerstar rs20v2  price-2692rs
https://www.banggood.com/4X-Racerstar-RS20A-V2-New-20A-Blheli_S-OPTO-2-4S-ESC-Support-Oneshot42-Multishot-for-FPV-Racer-p-1074732.html?rmmds=search?p=AL24049130595201702U

Hglrc flame f4 Flight controller, pdb, osd current sensor all in one  price-2297
https://www.banggood.com/F4-FLAME-Race-Spec-STM32F405-Flight-Control-Built-in-BETAFLIGHT-OSD-5V-BEC-PDB-Current-Sensor-p-1136917.html?p=AL24049130595201702U

Propellors look at quadkopters.com, they are indians, have huge variety of props, go for the dal cyclone 5045c  crystal propellor, around 190 per pack of 4 props.

It totals around 7000rs, but you will get amazing performance.
It has all the parts which were listed in the king kong kit.

You will also need frame, video transmitter and camera(if you want fpv, and have fpv goggles). These are also not included in the kingkong kit.
I would recommend this setup over the kingkong build.
If you want i can also suggest you the frame and other parts listed above.

Thanks for the suggestions

 But actually I am building my frame by self
And the controller to by using nrf module and arduino

And for flight controller I want to use kk mini avalaible on
Quadcopter for 795


Thanks a lot

Then leave the flight controller,
Go with the motors that i suggested,
Use  compatible esc which you want, or the ones which i have listed below. You will also need a power distribution board,

ESC- racerstar rs20a price-
1641 https://www.banggood.com/4X-Racerstar-RS20A-20A-BLHELI_S-OPTO-2-4S-ESC-Support-Oneshot42-Multishot-for-FPV-Racing-p-1064324.html?p=AL24049130595201702U
They are under restocking.

Good luck for your build.

You had helped me a lot
Can you do me a one more favour

Actually ESC what I had used were having 3 wires for the radio connection or can say for input but these were having only 2
Please help me out for this and describe how to use it

You were so helpful to me
Thanks

# tushar

The three wires in the esc you were using were,  a 5volt out to power flight controller, a ground and a signal wire.
The esc that i mentioned only have two wires, the ground and the signal. You will have to buy a power distribution board with 5v and 12v regulator, and use 5v from that to power flight controller( search for matek pdb on banggood, the one with 5v and 12v).
To use these esc, just connect their signal wire to signal pin on flight controller and ground wire on ground pin. To power flight controller, solder 2 wires to pdb, one wire on the 5v pad, and other on the ground pad, then just connect the 5v wire to the place where you would have connected the red wire(5v out wire) of the esc you were using and connect the ground wire on any ground pin on flight controller.

Thanks a lot

For giving your precious time and information to me

You were really helpful to me

If you want

Can I know something about you
Like what are you doing or anything like that


# tushar

I'm a 16 yrs old, currently in class 12. Preparing for nda.

Okk

All the best

You are persuing your 12 from which school

And do you also do programming with ardiuno

Or have participated in any competition related to this



#tushar

I study in a cbse school in ghaziabad,up.
I do not program arduino.
My interest is rc planes and fpv racing quads.

you can buy all these parts locally in delhi ,check multirotor section of www.hobbyxyz.com

thankyu bro

 but i am from Gujarat

and the items i wanted is not on hobbyxyz

any more suggestion from anyone