RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: November 08, 2009, 09:26:50 AM »
rckatty
Plane Lover
Senior Member

***

Reputation Power: 2 
rckatty has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Intermediate
Posts: 172
Join Date: Mar, 2009




I found this very interesting article

PRE FLIGHT PREP

Manufacturers strive to design and build ARF kits that an RC pilot can proudly show off and enjoy for many years, and more often than not, they are enormously successful. The quality, appearance and flight capabilities of the planes available today are truly outstanding, and I am among those who want to ensure that my new models will still be around for

me to enjoy 10 years down the road. Fortunately, a little extra time during the final assembly will help extend the life of that new plane. Try out some of these tips on your next ARE

1 SEAL DOWN LOOSE COVERING

This should be the first step in the assembly of any ARF that uses heat-- shrink covering. Use an iron or heat gun to remove wrinkles that may have emerged during shipping, and then turn the heat up and go over all the surfaces where the covering overlaps or ends on bare wood. Be sure you don't melt or shrink the covering too much, and pay particular attention to the engine compartment and wing-saddle areas. After you've sealed the covering where it ends on bare wood, apply CA along the edges to ensure that it stays that way.

2 FUELPROOF THE FIREWALL

After a few flights, the firewall or engine compartment of planes powered by nitro and gas engines can incur damage if left unprotected. Check these areas, and if needed, paint, epoxy and CA can provided the necessary protection. (Heat-shrink covering material will not sufficiently protected these areas from repeated exposures to fuel and gas residue.) The paint can be sprayed or brushed on, and the epoxy should be thinned with a little rubbing alcohol and applied with a brush. Thin CA can be dripped on the sur- face and allowed to soak in, but thick CA should be rubbed in with your finger; of course, it's a good idea to wrap your finger in plastic.

After a few flights, the firewall or engine compartment of planes powered by nitro and gas engines can incur damage if left unprotected. Check these areas, and if needed, paint, epoxy and CA can provided the necessary protection. (Heat-shrink covering material will not sufficiently protected these areas from repeated exposures to fuel and gas residue.) The paint can be sprayed or brushed on, and the epoxy should be thinned with a little rubbing alcohol and applied with a brush. Thin CA can be dripped on the sur- face and allowed to soak in, but thick CA should be rubbed in with your finger; of course, it's a good idea to wrap your finger in plastic.

3 CHECK HIGH-STRESS GLUE JOINTS

All visible glue joints should be checked for cracks or stress breaks when you unpack a new kit. Damage can easily occur during shipping; changes in humidity levels from one part of the country to another can warp parts and cause cracks or other damage to joints. When checking the joints, pay particular attention to high-stress areas such as the wings, stabilizer, rudder, firewall, landing-gear attachments and servo trays. Repair the damage with CA or epoxy, and reinforce that area with balsa triangle stock, plywood, or fiberglass cloth.

All visible glue joints should be checked for cracks or stress breaks when you unpack a new kit. Damage can easily occur during shipping; changes in humidity levels from one part of the country to another can warp parts and cause cracks or other damage to joints. When checking the joints, pay particular attention to high-stress areas such as the wings, stabilizer, rudder, firewall, landing-gear attachments and servo trays. Repair the damage with CA or epoxy, and reinforce that area with balsa triangle stock, plywood, or fiberglass cloth.

4 RUBBER TUBING AROUND THE CLEVIS

When the control surfaces deflect, pressure builds on the control horn and the clevis. The weakest link is the clevis - specifically, on its tiny pin. The pressure can generate enough force to pop that clevis pin loose, but rubber tubing will help prevent this.

5 REINFORCE THE SCREW HOLES WITH CA

All screw holes in wood (balsa, plywood and hardwood) should be reinforced with CA, especially those for the control horns, servos, canopy and cowl. Drill the hole, insert the screw and remove it, and then drop thin CA into the hole. This will strengthen the wood and prevent it from being stripped.

6 SEAL FUEL-TANK TUBING AT THE FIREWALL

Tubing that exits through holes in the firewall will eventually wear out from vibration, but you can prevent this by sealing the fuel tubing at the firewall with silicone sealant. Tanks that extend through the firewall should also have sealant around the hole; this will stop any fuel from seeping into the tank compartment .

7 PROPERLY INSTALLING THE HINGES

The CA hinges that are included in many ARF kits do a fine job of supporting the control surfaces. They are usually chemically treated to encourage the CA to wick to all parts of the hinge and provide good adheston, but this process can be helped along by drilling a small hole (3/32 inch) in the center of each hinge slot. This gap above and below the hinge will allow the CA to penetrate all the way to the back of the hinge.

8 FOAM TAPE ON THE WING SADDLE

Exhaust residue that enters through the wing saddle can damage unprotected wood in the plane's interior and will eventually ruin it. You can protect this area by applying foam tape around the wing saddle. It will form a fuel-- proof seal and is soft, so it won't hinder wing alignment.

9 THREAD-LOCK ALL BOLTS

With the exception of engine screws, all of the bolts that screw into nuts, blind nuts and threaded metal pieces benefit from threadlock. It reinforces the grip and provides a measure of insurance that the screws won't vibrate loose. This simple step can save you quite a bit of grief later.

With the exception of engine screws, all of the bolts that screw into nuts, blind nuts and threaded metal pieces benefit from threadlock. It reinforces the grip and provides a measure of insurance that the screws won't vibrate loose. This simple step can save you quite a bit of grief later.

10 KEEP THOSE WHEELS ROLLING

To ensure that the wheels remain in place, use a small file or a rotary tool to grind a small flat spot on the axle beneath the wheel-collar setscrew. This flat spot will prevent the wheel collar from sliding off. Don't forget to apply thread-lock to the setscrew.

So, the next time you're getting ready to build a new ARF, remember these tips. By following just a few, you can extend the life of your favorite ARF. If you follow them all, you'll enjoy that plane for many years to come. Good luck!

http://findarticles.com/p/articles/mi_qa3819/is_200304/ai_n9207515/?tag=content;col1
Logged

Hangar: SU27 .90, Escape .46,
RDS8000 2.4ghz,
GS Racing 1/8 Truggy,
KM 1/5 Baja,
MX-3 FHSS,
coming soon *XRAY XB808*
 

Read
« Reply #1 on: November 08, 2009, 09:51:11 AM »
anwar
Administrator
Forum Hero

*****

Reputation Power: 141 
anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!anwar is awe-inspiring!
Offline Offline

City: Doha (Qatar) & Thrissur
State: Kerala
RC Skills: Advanced
Posts: 11619
Join Date: Mar, 2009

RC India - Flying and racing with open minds !



Good stuff  Thumbs Up
Logged

Hangar : Please see my introduction.
RC India forum and me : About this forum.
 

Read
« Reply #2 on: November 08, 2009, 10:06:51 AM »
rckatty
Plane Lover
Senior Member

***

Reputation Power: 2 
rckatty has no influence.
Offline Offline

City: Bangalore
State: Karnataka
RC Skills: Intermediate
Posts: 172
Join Date: Mar, 2009



Thanks  Wink
Logged

Hangar: SU27 .90, Escape .46,
RDS8000 2.4ghz,
GS Racing 1/8 Truggy,
KM 1/5 Baja,
MX-3 FHSS,
coming soon *XRAY XB808*
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
TREX NITRO PRO ASSEMBLY « 1 2 3  All »
Helis
second_chance 67 27992 Last post February 07, 2011, 12:51:09 AM
by Ajay JM
F 18 Hornet Profile Catapult Glider Assembly Log
Beginners Zone
VC 12 11121 Last post September 01, 2010, 10:07:21 PM
by VC
RC Bazaar TB- 20 Assembly/Build Log « 1 2  All »
Electric Planes
akky 45 26964 Last post July 15, 2011, 07:27:53 PM
by akky
new head assembly - wobbles - 450 v2 (hiller head assembly)
Helis
dheerajjuneja 12 8460 Last post August 08, 2012, 12:04:39 AM
by Hellyflyer
Need Kk 2.15 quadcopter assembly tips help plz
Multirotors
krupashree 9 4825 Last post January 27, 2017, 05:53:04 PM
by krupashree