9053 volitation helicopter - newbie need help in fine tuning the trim

Started by ranjan, July 26, 2010, 07:34:09 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

saumil_b

Can someone please help me with the Volitation 9053. Didnt come in my box!!  I am a first time flyer and am completely lost!!

anwar

Welcome to RC India :)

Please do post in detail about what exactly the problems are, preferably with a video. 
Hangar : Please see my introduction.
RC India forum and me : About this forum.

saumil_b

Dear Anwar, I am an absolute newbie and when i opened my box, the Manual was missing. Would appreciate if someone could share one with me please.

shubhambilawar

even me 2

got a new 450 v2 rtf from rcbazaar
& the manual was missing
i asked rcb & they told manufacturer doesn't supply the manual with the kit
but operated it its working fine

FS TH9x |450v2|seagull 40|Hiller pro 450|Futaba6ex|Scanner| Futaba 6EA|paragon |Hirrobo Suttle Plus|
www.facebook.com/shubhambilawar

saumil_b

Shubham, the Manual is there, its at the back of the Thermacol, i saw it while we checked ours but probably was dropped sumwer there :( Can someone help US now !!

shubhambilawar

i searched it every where
but its not there
so asked rcb
they told me to download it from net
for trex 450v2
FS TH9x |450v2|seagull 40|Hiller pro 450|Futaba6ex|Scanner| Futaba 6EA|paragon |Hirrobo Suttle Plus|
www.facebook.com/shubhambilawar

saumil_b

So do you have anything?? If so can you send me the Link here..

anwar

The manual for 9053 seems hard to find online.  It would be good if someone can scan and upload it.
Hangar : Please see my introduction.
RC India forum and me : About this forum.

shubhambilawar

rcb told me about this http://www.helifreak.com/
we will get all the helicopters manuals here :thumbsup:
but we have to register here first
FS TH9x |450v2|seagull 40|Hiller pro 450|Futaba6ex|Scanner| Futaba 6EA|paragon |Hirrobo Suttle Plus|
www.facebook.com/shubhambilawar

saumil_b

No manual there as well.. Does anybody have a manual and is willing to help!!

Hellyflyer

Hi

9053 is a very simple 3.5 heli with Gyro Very stable, just make sure that you try to fly it in open space. Please pm me your email ID and I will send you the manual.

Thanks
Hellyflyer
Helis and Quads ROCK !!

saumil_b


me112

my id is [Please enable JavaScript to see this content]
plzzzz send me manual

peter.gomes

Hi All,

Today I received the 9053 volitation helicopter for my son as a christmas gift to him & I did some modification with the TX .Instead of regualr batteries in TX , I used my NICD battery TX Pack (eight cell) on the TX of (9053) .

Before I did the check the voltage  which read 12.15v on my lipo Charger in Nicd mode then I connected it to the 9053 volitation helicopter  TX which was giving full reading throttle trim was also working (lights up but no heli  response) & also the throttle stick working (lights up but no heli  response) later I switched on Heli & then the TX but there was no BONDING or any kind of response to the heli?

Again I tried it several time & even waited a several mintues (10 or 15 minutes)

Is it becuase that Tx is designed only for alkaline batteries ? Or Nicd Does not work with these TX ?

Awaiting for your reply.

Regards
Peter

Hellyflyer

Helis and Quads ROCK !!

peter.gomes

Hi

thanks for your prompt reply

Did not try that but I intend to do it if required as I Would need to re -solder the old connector to the eight cell holder.

Im no electronic guy so very little know of Electronic

What you think about my IDEA of Nicd batteries for 9053 TX ?should it work ?

regards
Peter

peter.gomes

Hi All,

Today I again bought 8 duracell batteries & installed it in the TX & Then switch on the Heli & then Tx .

Remove the canopy to check all light are working or not.When switch on heli ,noticed that on the PCB of heli ,the Red light was blinking(may be its trying to bind) .Tx is also ON  -throttle right down & the same with throttle trim ,waited for 5-10  mintues with TX ON -slowly raised the throttle but no response,then tried the throttle trim at 1/4 ,then half but no response.Tx voltage on multimter reads as 26v. 

How do I verify whether the tx is working or not or binding.

Any kind of help or suggestion

regards
Peter

peter.gomes

Hi All,

After several hours of checking & trying to verify the tx or Heli ,signal found the bloody problem .Only when the Tx is kept at 4 inches away from the heli PCB there is binding.All of a sudden the heli just sprang to life & I was dazzled.On further checking noticed that the distance is creating a problem,so check the Heli antena wire if its cut or booken with the multimeter continuity test & it was ok ,then check the Tx Antena whether its properly attached or not & sanded both send of the antena & where the antena is put in tx.But no result.

Checked the voltage on Tx read as 26.2v -(8 duracel battery aklaline) & on heli it read as 17.2v.li lion battery (checked on multimeter)

what could be the problem

regards
Peter

peter.gomes

Dear Anwarsab & All,

Need some help

Just to further update you that this model was purschased from Ebay.
26" Large 3.5 Channel Remote Control RC Gyro Helicopter Metal Frame - 9053 Rs.3,798.00 11/12/11 16/12/11 21/12/11 30366577331  & I also informed TEJ India -Delhi  the current Situation & he informed me that his engineer would speak to me but no response.
Since its Defective  & bought from e bay ,Does any one know what is the process of sending  back the defective via e bay? Using  ebay for the first time.would Ebay replace the set ? or refund me ?

But I've already tampered the orignal connector & replaced them with (futaba connector for TX ) & Also on the Heli  BATTERY &  CHARGER POINT put XT60 on them.so I can use my other LI PO BATTERY.

Regards
Peter


regards Peter

peter.gomes

Hi ALL,


There was a problem with the multimeter,I again crossed checked with my lipo charger .The battery on my 9053 is 8.1v & Tx is 11.8v

Late night I did open the tx ,checked all solders & seen all visual electronic parts are ok,again close it & seen a range check,Beileve me the TX could responds at 13 to 14 ft after that the binding stop & blinking thrice (3 blinks & then a gap ).

Spoke to seller & he seem to say that the TX may be faulty & suggested to center the knob on the right side of the TX(RUDDER TRIM) & as per him if you turn it correctly it may go into auto mode thereby give you full signal,Tried that stuff too but still at 13 to 14 ft only but now I can atleast fly it around a raduis of 6ft.The seller also suggested that to send the Tx back to him as he suspects its faulty.He too is no electronic engineers just out of his selling experience,he suggested me the knob trick(but did not work for me).
I've even changed the external tx Antena from one of my old Futaba Tx -6va & its did work but the range was 8ft to 9ft.Therefore put the original back into its place.
So far so good -Do you suspect the TX ?

Regards
Peter