Sir
I am planning to buy this kit
What does the expert say about this
Http://www.aliexpress.com/item/Carbon-Fiber-Mini-ZMR250-C250-Quadcopter-2204-2300kv-Motor-simonk-12A-Esc-CC3D-Flight-Controller- 5030 /32584315564.html
High Quality Carbon Fiber Mini 250 FPV Quadcopter Frame Mini Quad Frame Holder
Description:
1.5mm carbon fiber fuselage
Machine arm 3.0mm
Aluminum Jin Zhuzai
AV shockproof ball
FPV installed by edition
Screw
Specifications:
- Main material: Full carbon fiber
- With rubber damper to decrease vibration during flight
- Aluminum alloy spacer, light weight, reliable
- Wheelbase: 250mm
- Weight: 135.1g
package including:
1 set 250 quadcopter frame kit ( not assembled )
1 pcs CC3D EVO flight controller with yellow shell
4 pcs 2204 2300kv motor( 2CW, 2CCW)
4pcs Emax BLHeli 12A ESC
1pcs CC3D distribution board
8pcs 5030 propellers (2 pairs green, 2 pairs black)
you can also check this , all parts in delhi
http://hobbysea.com/index.php?cPath=66
@hangingthough, how much are u ready to invest in this? because there are better more long lasting options that come for a little bit more than that LHS's offer.... u can go for 2205 2300 kv motors and better ESC's (FVT little bee or DYS 20a blheli's) that are a great option... buying an ARF means that if something goes wrong u may not have another option to buy just the damaged part but the whole set of the part... so basically a bad crash costs 4 times of what was damaged... and there are too many frames out there! and 5030 are a bad choice of props that every ARF sells :P 5040-6040 for a 2300 kv motor gives thrust and less noise ;)
If you are getting the ZMR 250 frame you should get the ZMR power distribution board from quadkopters.com instead of using a separate PDB. It is also better to invest in 20A ESCs. Also, you'll need a 3S LiPo of around 1500mAH and a Rx/Tx to complete the build. Are you going to buy FPV gear too?
Quote from: Supafly on July 27, 2016, 07:07:23 PM
If you are getting the ZMR 250 frame you should get the ZMR power distribution board from quadkopters.com instead of using a separate PDB.
Terrible advice, don't do this. Always better to get a separate PDB, I recommend the matek ones.
Quote from: Cycloned on July 27, 2016, 07:22:56 PM
Quote from: Supafly on July 27, 2016, 07:07:23 PM
If you are getting the ZMR 250 frame you should get the ZMR power distribution board from quadkopters.com instead of using a separate PDB.
Terrible advice, don't do this. Always better to get a separate PDB, I recommend the matek ones.
@cycloned: it seemed to me that having the PDB built into the frame would facilitate an easier and cleaner build.
Anyway, I am here to learn, so can you please explain why a separate PDB would be better?
If anything goes wrong with the PDB since u will crash, it's easier to replace and the upgrades also will have enough space as u can stack the PDB and FC (better CG as FC gets a little lift, closer to the batter :P ), and crashs will be more forgiving as the PDB plate can crack too, it works out cheaper and safer...
Yup, as Rathi said, integrated PDB is more vulnerable to breaking. It's better to have a carbon fiber bottom plate with the PDB mounted inside on standoffs.
Plus weight 😝
Do cc3d have auto stabilization mode
yeh it does, go to the configuration and set it up... It's called attitude mode