Print Page - Alsan from Bangalore

Title: Alsan from Bangalore
Post by: alsanrocks on August 25, 2011, 06:30:26 PM

Hi All.. I'm Alsan.. work as a salesman in Bangalore. I'm very new to rc but dreamt of it a lot as couldn't afford then.
I would love to build a plane myself from scratch.. But don't even know the basic of designs and aerodynamics.

I have a design in mind.. thou got it in forum itself. Pls help

Moderator Note: moved to RC people, subject modified

Title: Re: hi all
Post by: PankajC on August 25, 2011, 06:40:16 PM

Hi Alsan, welcome to the forum. When I was younger, I had also dreamt of someday flying RC - but then I could not afford it.

Anyway, since then I have also done lot of build - launch - crash - build again cycles and am still learning to build and fly. I am sure you will find the folks very helpful here.

however, if you can, try and meet with some local flyers in your area. It will help shorten your learning experience and also mean less initial monetary load to get into RC.

regards
Pankaj

Title: Re: Alsan from Bangalore
Post by: alsanrocks on August 25, 2011, 07:42:18 PM

hi pankaj. thnx for your prompt reply.. hope to find some helping hand soon to get started..

Title: Re: Alsan from Bangalore
Post by: alsanrocks on September 08, 2011, 12:51:22 PM

hi all, could anyone give me a link or so where i could learn the basics.

Title: Re: Alsan from Bangalore
Post by: iamahuman on September 08, 2011, 07:56:34 PM

The RC India Gems (http://www.rcindia.org/rc-india-forum/the-rc-india-gems/)

Title: Re: Alsan from Bangalore
Post by: gbisht on September 16, 2011, 12:53:12 AM

Hi All,
Please help Alsan and me also, I just started in RC hobby with heli and cars.
but now I want to build a small (indoor or outdoor) plane, just easy and basic

But I want to use my scrab, I have 2 * micro co-axial Heli with in build gyro and without gyro.

so I am planing to build figure 1 plane were I want to use 2 motors and also use gyro (may be i can use Aleron by 2 motors)and 3rd motor I will use for manage Elevator.

or

and in Figure 2 I will use total 2 motors, 1 for throtal and 1 is for elevator

Please forgive me to talk like a fool..... (:|~

and yes I have built Hot Wire Foam Cutter...

Title: Re: Alsan from Bangalore
Post by: iamahuman on September 16, 2011, 07:30:29 AM

Check Reply#4...

Title: Re: Alsan from Bangalore
Post by: gbisht on September 18, 2011, 02:08:09 AM

Hi Friends,

I have made my first foam Micro Plane, by using Home made Hot wire Cutter, Normal 1 inch foam and thermacol food plates for wings and tail. for make it little strong I have covered it with Celo Tape.

for electronics I have used my old 3-Ch micro Heli. used its 2 Coxial motors (as you can see on Wings) and tail motor used as Servo...lol (not very much efficient).

So done flight last night, and found heli is going up direction, so now read about CG and now prepair accordingly.

Can any one suggest how we can use motor as a servo (it is not working good because circuit is not providing enough power to motor, just like main motors).

Title: Re: Alsan from Bangalore
Post by: gbisht on September 18, 2011, 02:17:28 AM

few more, after CG and Motor base servo and more mAh battry after fail flights.

RC India

General Topics => RC People => Topic started by: alsanrocks on August 25, 2011, 06:30:26 PM