Print Page - Planning to get an RTF after self made trainer disaster

Title: Planning to get an RTF after self made trainer disaster
Post by: rishi13 on April 27, 2015, 10:15:59 PM

Hello everyone,
I'm new to RC hobby. I had made a trainer plane with foam based on this website http://mikeysrc.com/Sport-Trainer.html (http://mikeysrc.com/Sport-Trainer.html)
however, my rc plane broke up in pieces during launch itself after crashing to the ground. Now, I plan to buy an RTF. Pleas advice me which RTF to buy and from where. I have the following components:
-9gm servos- 3 nos
-brushless motor-1200kv
-30amp esc
-1300mah li-po
-10x6 prop
-CT6B Tx and Rx
please suggest a plane in which I can use all my components. I am based at NOIDA and I am 11 years old.
Thanx

Title: Re: Planning to get an RTF after self made trainer disaster
Post by: K K Iyer on April 27, 2015, 11:56:43 PM

See PM please

Title: Re: Planning to get an RTF after self made trainer disaster
Post by: rishi13 on April 28, 2015, 09:14:49 AM

KK Iyer sir, these are the detals of the battery and motor you asked-
-Motor-Spec.
Weight: 39g
Shaft: 3mm
Motor Length: 46mm
Diameter: 28mm
Stator Size: 22x10mm
Suggested prop: 9~10inch
Voltage: 11.1v (3S)
Kv: 1200RPM/V

Data ;
Prop size: 10x5
RPM: 7700
Max Curr: 15A
Thrust: 840gm

Prop size: 10x4.7 SF
RPM: 7100
Max Curr: 16.5A
Thrust: 850gm

-Battery -Capacity (mAh) - 1300
Voltage (V) - 11.1
Cells (S) - 3
C Rating (C) - 20
Size (L*W*H) mm - 72*36*25
Weight (g) - 120
Max Charge Rate - 2.0C
Max Current (A) - 1.5
Plug/Connector - XT60

Regards.

Title: Re: Planning to get an RTF after self made trainer disaster
Post by: ashimda on April 28, 2015, 09:32:22 AM

With the electronics you have, you could look at this...http://www.vortex-rc.com/5-vt-speedster/15-vt-speedster.html?sid=3687de37a3b6a8e06774d43c8c0fabaa (http://www.vortex-rc.com/5-vt-speedster/15-vt-speedster.html?sid=3687de37a3b6a8e06774d43c8c0fabaa)

Title: Re: Planning to get an RTF after self made trainer disaster
Post by: rishi13 on April 28, 2015, 01:55:47 PM

The above linked plane is costing 1,950rs. Can I get something under 1,000rs ?
This is the plane I made-

Title: Re: Planning to get an RTF after self made trainer disaster
Post by: vishnudsvsk on April 28, 2015, 02:24:14 PM

where to buy EPP foam in kerala, trivandrum.....any store?

Title: Re: Planning to get an RTF after self made trainer disaster
Post by: rishi13 on April 29, 2015, 11:15:59 AM

I am thinking to buy this plane-http://www.rcbazaar.com/product.aspx?productid=1063 (http://www.rcbazaar.com/product.aspx?productid=1063)
Please advice me if it is a right beginners plane. Thanx

Title: Re: Planning to get an RTF after self made trainer disaster
Post by: K K Iyer on April 29, 2015, 09:03:33 PM

@rishi13,
Excellent choice. We have 3 here now.
But shipping will add about 1000. So it will be about 6000.
Thought your budget was 1000.

Incidentally, if you existing model is not completely destroyed, try doubling the area of the stabilizer/ elevator.
To me it looks like the horizontal tail area is too small in the mikeyrc plan.

Edit:
Post a top view pic if possible.

Title: Re: Planning to get an RTF after self made trainer disaster
Post by: rishi13 on April 29, 2015, 10:50:21 PM

I will post the pic tomorrow.

RC India

General Topics => Beginners Zone => Topic started by: rishi13 on April 27, 2015, 10:15:59 PM