RC India

Turnigy 2650mAh 3S 20C Lipo Pack

The new Turnigy Lipoly packs deliver full capacity at the said C rate.
You wont find a better deal in Lithium Polymer batteries anywhere!

Spec.
Minimum Capacity: 2650mAh
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 20C
Peak Discharge (10sec): 30C
Pack Weight: 225g
Pack Size: 137 x 43 x 17mm
Charge Plug: JST-XH
Discharge Plug: Female XT60

BUY IT NOW :-
http://www.rcproduct.in/turnigy-lipoly-batteries/26-turnigy-2650mah-3s-20c-lipo-pack.html (http://www.rcproduct.in/turnigy-lipoly-batteries/26-turnigy-2650mah-3s-20c-lipo-pack.html)

(http://www.rcproduct.in/99-thickbox_default/turnigy-2650mah-3s-20c-lipo-pack.jpg)

ZIPPY Flightmax 4000mAh 3S1P 20C
Zippy Flightmax batteries deliver full capacity & discharge as well as being the best value batteries in the hobby market today!

Spec.
Capacity: 4000mAh
Voltage: 3S1P / 3 Cell / 11.1v
Discharge: 20C Constant / 30C Burst
Weight: 306g (including wire, plug & shrink wrap)
Dimensions: 146x51x22mm
Balance Plug: JST-XH
Discharge Plug: Bullet Connector

BUY IT NOW :-
http://www.rcproduct.in/batteries-accessories/15-zippy-flightmax-4000mah-3s1p-20c.html (http://www.rcproduct.in/batteries-accessories/15-zippy-flightmax-4000mah-3s1p-20c.html)

(http://www.rcproduct.in/61-thickbox_default/zippy-flightmax-4000mah-3s1p-20c.jpg)


ZIPPY Flightmax 2500mAh Transmitter Pack (Futaba/JR)

The Zippy Flightmax 2500mAh Transmitter pack fits snuggly into any Futaba or Jr radio which takes a 4x4 AA cell battery configuration (see image).

With a capacity of 2500mAh this lipoly replacement for your old NiCD or NiMH will last four to five times longer. Probably the best advantage with a lipoly transmitter battery is that it will give a true voltage reading from start to finish which means you can say goodbye to the days where you thought your Transmitter was fully charged at home, only to find the voltage drop off rapidly when at the field.

Spec.
Capacity: 2500mAh
Voltage: 11.1v
Constant discharge: 3-5C
Burst discharge: N/A
Weight: 146g
Size: 100x28x23mm
Plugs: Futaba, JST-XH, JR/Spektrum

BUY IT NOW :-
http://www.rcproduct.in/transmitter-lipo-pack/20-zippy-flightmax-2500mah-transmitter-pack-futabajr.html (http://www.rcproduct.in/transmitter-lipo-pack/20-zippy-flightmax-2500mah-transmitter-pack-futabajr.html)

(http://www.rcproduct.in/74-thickbox_default/zippy-flightmax-2500mah-transmitter-pack-futabajr.jpg)


ZIPPY Flightmax 3000mAh 3S1P 20C

Zippy Flightmax batteries deliver full capacity & discharge as well as being the best value batteries in the hobby market today!

Spec.
Capacity: 3000mAh
Voltage: 3S1P / 3 Cell / 11.1v
Discharge: 20C Constant / 30C Burst
Weight: 239g (including wire, plug & shrink wrap)
Dimensions: 137x45x18mm
Balance Plug: JST-XH
Discharge Plug: XT60

BUY IT NOW :-
http://www.rcproduct.in/zippy-lipoly-batteries/25-zippy-flightmax-3000mah-3s1p-20c.html (http://www.rcproduct.in/zippy-lipoly-batteries/25-zippy-flightmax-3000mah-3s1p-20c.html)

(http://www.rcproduct.in/98-thickbox_default/zippy-flightmax-3000mah-3s1p-20c.jpg)


Turnigy 9XR Transmitter Mode 2 (No Module)
The greatly anticipated Turnigy 9XR has arrived!

The software for the 9XR first began development 6 years ago. Since then it has been tweaked, tuned, changed, updated and revamped by members of the R/C community into a powerful - yet easy to use interface. Our engineers designed the physical product around the R/C communities software changes and input. The culmination of all these is the Turnigy 9XR!

For many users this will be the perfect 9 channel radio straight out of the box, but there are many tinkerers out there who love modifying and pushing the boundaries of what is possible from their radio. We have factory fitted the 9XR with an AVR ISP header to simplify the development of custom software, we have launched turnigy9xr.com as the epicentre for software developers and additional community support for all 9XR users......With the 9XR we encourage it!

The 9XR is supplied preloaded with top quality software which is full of features and yet remains easy to use. Our aim was to develop a radio for you, the hobbyist, with an extensive list of standard features usually expected from a radio system 3 times the price. Our Turnigy 9XR is everything you imagined and more!

9XR Standard Features:
• 8 Channel PPM/9 Channel PCM
• Full Ball Bearing gimbals
• Adjustable Stick Length
• Digital Trims on all Primary Axis
• 16 Model Memory
• Assignable Switches
• Freely Assignable Channel Mixes
• Graphical Dual Rate and Exponential
• Sub Trim and Travel Adjust
• Flaps and Differential
• Throttle Hold
• Supports Heli/ Aero/ Glider Model Types
• Programming Templates Based on Model Type
• Supports M1, M2, M3, M4 stick modes
• 128 x 64 backlit Liquid Crystal Display
• Built in JR & Futaba Trainer Ports
• PPM & PCM Output
• JR Form Factor RF Modules (Orx Dsm2, Orx Open LRS 433Mhz etc)
• Programmable Timers
• Low Voltage Warning and Buzzer
• Supports 3s Lipo (Required)
• 9XR Firmware Pre-loaded
• AVR ISP Interface
• Internal 2.4GHz Antenna

Online support and user forums available at: www.turnigy9xr.com (http://) (http://) (http://)

Spec:
Channnel: 8ch ppm/9ch pcm
Display: 128*64LCD (Backlit)
Support Type: Heli/Acro/Glid
Model Memory: 16
Stick modes: 1, 2, 3, 4
Encoder type: ppm/pcm
Module Interface: JR Compatible (See Related Items Below)
Simulator Interface: Yes (JR & Futaba)
Buzzer: Yes
Battery Compartment: 112 x 44 x 27mm
Weight (less battery & Rf Module): 723g

Required:
Battery 3S Lipo
RF Module

Included:
Turnigy 9XR Transmitter (Mode 2 – Throttle on Left Stick)
Quick Start guide


BUY IT NOW :-
http://www.rcproduct.in/2-4ghz-turnigy-india/8-turnigy-9xr-transmitter-mode-2-no-module.html (http://www.rcproduct.in/2-4ghz-turnigy-india/8-turnigy-9xr-transmitter-mode-2-no-module.html)

(http://www.rcproduct.in/27-thickbox_default/turnigy-9xr-transmitter-mode-2-no-module.jpg)


FrSky DJT 2.4Ghz Combo Pack for JR w/ Telemetry Module & V8FR-II RX
FrSKY ACCST technology is proven, approved by many model associations, tested and reviewed as the leading Chinese 2.4Ghz R/C Technology. If you think DSM2 or FASST is the best, think again!
New FrSKY ACCST (Advanced Continuous Channel Shifting Technology) gives you secure radio communicatios in 2.4Ghz band. ACCST 2.4GHz system shifts 80 channels around hundred times per second in the 2.4GHz band. This means that the system is completely resistant to interference in that band.
 
Features:
Advanced Continuous Channel Shifting Technology (ACCSTis our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility.
Easy to bind and very fast link-up.
Excellent reboot time.
True Diversity with two antennas.
All channels can be programmed with Failsafe, quickly and easily.
Quick and extremely stable in performance.
Precise and smooth servo response.
Extended range (1.5km-2.5km).
 
FrSky DJT is compatible with JR transmitters following:
JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, PX, 9XII, 11XZERO
 
Receiver Specification:
Operating voltage: 3.0~16V(HV Version)
Power consumption: 30mA
Resolution: 3072
Latency: 22ms
Number of channels: 8
Range: 1.5km-2.5km
Dimensions: 44 x 24 x 14 mm
Weight: 9.3g
 
Module specification:
Operating voltage: 6.0V-13.0V (can handle 3S!)
Power consumption: 50mA
Output Power:: 60mW
Resolution: 3072 (11bit)
Dimensions: 63.9x48.5x36.5mm

Included;
1 x 8-channel Telemetry Transmitter Module DJT
1 x Transmitter Antenna
1 x 8-channel receiver V8FR-II (HV Version)

BUY IT NOW :-
http://www.rcproduct.in/frsky-accst-module-india/11-frsky-djt-24ghz-combo-pack-for-jr-w-telemetry-module-v8fr-ii-rx.html (http://www.rcproduct.in/frsky-accst-module-india/11-frsky-djt-24ghz-combo-pack-for-jr-w-telemetry-module-v8fr-ii-rx.html)

(http://www.rcproduct.in/47-thickbox_default/frsky-djt-24ghz-combo-pack-for-jr-w-telemetry-module-v8fr-ii-rx.jpg)


Hobbyking KK2.0 Multi-rotor LCD Flight Control Board
Designed by the Grand father of the KK revolution, Rolf R Bakke, exclusively for HobbyKing, the KK2.0 is the evolution of the first generation KK flight control boards. The KK2.0 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed. simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and your ready to go! all of which is done with easy to follow on screen prompts!

The original KK gyro system has been updated to an incredibly sensitive dual chip 3 Axis gyro and single chip 3 axis accelerometer system making this the most stable KK board ever and allowing for the addition of an Auto-level function. At the heart of the KK2.0 is an Atmel Mega324PA 8-bit AVR RISC-based microcontroller with 32k of memory. An additional 2 motor output channels have been added to the KK2.0 allowing for a total of 8 motors to be controlled (Octocopter). A handy Piezo buzzer is also included with the board for audio warning when activating and deactivating the board.

If your new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.0 was built for you. The 6 Pin USBasp AVR Programming interface ensures future software updates will be quick and easy.

Specs.
Size: 50.5mm x 50.5mm x 12mm
Weight: 21 gram (Inc Piezo buzzer)
IC: Atmega324 PA
Gyro: InvenSense Inc.
Accelerometer: Anologue Devices Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us
Firmware Version: 1.2

Pre-installed firmware.
Dualcopter
Tricopter
Y6
Quadcopter +
Quadcopter X
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Aero 1S Aileron
Aero 2S Aileron
Flying Wing
Singlecopter 2M 2S
Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option)

The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.


Whats is a Multi-Rotor Control board you ask?


The HobbyKing KK2.0 Multi-Rotor controller is a flight control board for multi-rotor Aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the three on board gyros (roll, pitch and yaw) then passes the signal to the Atmega324PA IC. The Atmega324PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft.

The HobbyKing KK2.0 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega324PA IC via the ail, ele, thr and rud inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).

BUY IT NOW :-
http://www.rcproduct.in/multi-rotors-parts/12-hobbyking-kk20-multi-rotor-lcd-flight-control-board.html (http://www.rcproduct.in/multi-rotors-parts/12-hobbyking-kk20-multi-rotor-lcd-flight-control-board.html)

(http://www.rcproduct.in/50-thickbox_default/hobbyking-kk20-multi-rotor-lcd-flight-control-board.jpg)


325mm Carbon Fiber Main Blades
450 Size Carbon Fiber blades with reinforced root and balanced tip.

Spec;
Length: 325mm
Weight: 21g each
Grip : 5mm

BUY IT NOW :-
http://www.rcproduct.in/helicopters-parts/19-325mm-carbon-fiber-main-blades.html (http://www.rcproduct.in/helicopters-parts/19-325mm-carbon-fiber-main-blades.html)

(http://www.rcproduct.in/73-thickbox_default/325mm-carbon-fiber-main-blades.jpg)


WLtoys V911 - 2.4Ghz 4CH Micro Helicopter Mode 2 (RTF)
WLtoys V911 2.4GHz 4CH Remote Control RC Helicopter with Gyro Mode 2

The new Hobbyking FP100 2.4Ghz 4CH micro helicopter is a high performance fixed pitch heli at an unbelievable price! (Compare this to the Align Trex 100)

The Hobbyking FP100 is a very capable fixed pitch heli with two flight modes - standard and high performance (selectable by button on top of radio). By swithing to high performance mode, the swashplate throws are increased which makes the heli much more agile and gives it faster response. This also allows this micro heli to handle less than calm wind conditions, so makes it suitable for outdoor use as well!

The included 2.4Ghz radio is extremely high quality with its easy to read, brightly backlit LCD display and digital trim adjustment. This is an exceptional value compared to low quality radios that are generally included in other ready to fly kits.

This ready to fly kit includes a spare main blade set, spare tail blade, 2 x 3.7V 120mAh lipoly batteries, a dual charger which can be powered via included USB cable, and also a charge lead built in to the radio for charging when no USB connection is available. All you need to do is charge the batteries and your ready to fly!

You will not find a better deal on the market today for a fixed pitch micro helicopter of this quality!

Specifications:
Length: 215mm
Height: 84mm
Gross Weight: 31g with battery
Battery: 1S 3.7V 120mah Li-Po
Transmitter: 2.4Ghz Mode 2 (Throttle on the Left)
Flight Duration: 6-8 minutes

Included:
FP100 4CH micro helicopter
2.4Ghz mode 2 rado w/backlit LCD display
2 x 3.7V 120mAh lipoly
Dual slot battery charger w/USB charge cord
Spare main blade
Spare tail blade

Required:
6 x AA size batteries

BUY IT NOW :-
http://www.rcproduct.in/ready-to-fly-rtf/18-hobbyking-fp100-24ghz-4ch-micro-helicopter-mode-2-rtf.html (http://www.rcproduct.in/ready-to-fly-rtf/18-hobbyking-fp100-24ghz-4ch-micro-helicopter-mode-2-rtf.html)

(http://www.rcproduct.in/72-thickbox_default/hobbyking-fp100-24ghz-4ch-micro-helicopter-mode-2-rtf.jpg)
(http://www.rcproduct.in/71-thickbox_default/hobbyking-fp100-24ghz-4ch-micro-helicopter-mode-2-rtf.jpg)

Hi,

Do you have 2S/3S high mah lipos of below dimensions, i need for my traxxas 1/16 e-revo car

Dimensions: 3.5 x 0.8 x 1.8" (88 x 20 x 35mm) / 3.6 x 0.63 x 1.3" (91 x 16 x33mm)

Also i need one small nimh battery pic attached, let me know if have one.

Thanks

No,
I have not.
But you can check www.rcproduct.in (http://)
Maybe you find similar battery for your traxxas 1/16 e-revo car.

Thanks.

Hi,

Please check here for more contact information,

http://www.rcproduct.in/content/6-contact-us (http://www.rcproduct.in/content/6-contact-us)
[Phone number and Address]

http://www.rcproduct.in/contact-us (http://www.rcproduct.in/contact-us)
[Direct email Contact]

we also provide a Phone number and our Address also...

Thanks.

You should list your contact address properly.

This has contact information, that is in the side bar.

http://www.rcproduct.in/content/6-contact-us (http://www.rcproduct.in/content/6-contact-us)

This does not, and it is in the main menu.

http://www.rcproduct.in/contact-us (http://www.rcproduct.in/contact-us)

And out of curiosity, you NEVER refund anyone under any circumstance ?

http://www.rcproduct.in/content/7-refund-and-cancellation-policy (http://www.rcproduct.in/content/7-refund-and-cancellation-policy)


And one cannot cancel an order even before shipping ?

Seems very different from other stores.

http://rcbazaar.com/ShippingInfo.aspx (http://rcbazaar.com/ShippingInfo.aspx)

http://www.rcdhamaka.com/index.php?main_page=shippinginfo (http://www.rcdhamaka.com/index.php?main_page=shippinginfo)

Refund is possible in Some cases...
But cancellation is only possible Before shipping Not After Shipping.

Policy is changed...


Thanks Anwar for this.

A reasonable refund policy that does not bring financial burden to the store will be re-assuring to the customers.

There seems to be absolutely NO reason why they have to be listed separately. The address and phone should be listed in both places.

No worries...

I will add my Address and Phone number on Both place...

Thanks for suggestion to Improve site contact information and we are also providing live chat option ...

On Left sidebar [Live chat]
or
http://www.rcproduct.in/chat/client.php?locale=en (http://www.rcproduct.in/chat/client.php?locale=en)

• Contact information added on Both places.
• Refund and order cancellation policy also added.

Welcome for any type of suggestion.
Thanks

Re-Stocked Turnigy 2200mAh 3S 20C Lipo Pack
Spec.
Minimum Capacity: 2200mAh (True 100% Capacity)
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 20C
Peak Discharge (10sec): 30C
Pack Weight: 185g
Pack Size: 103 x 33 x 24mm
Charge Plug: JST-XH
Discharge Plug: XT60

BUY IT:-
http://www.rcproduct.in/turnigy-lipoly-batteries/17-turnigy-2200mah-3s-20c-lipo-pack.html (http://www.rcproduct.in/turnigy-lipoly-batteries/17-turnigy-2200mah-3s-20c-lipo-pack.html)

(http://www.rcproduct.in/65-thickbox_default/turnigy-2200mah-3s-20c-lipo-pack.jpg)

By
www.rcproduct.in (http://)

WLtoys V911 - Hobbyking FP100 2.4Ghz 4CH Micro Helicopter Mode 2 (RTF) [FREE SHIPPING]

Free shipping By EMS.
Only Available for Few 5 Days.


BUY IT NOW :-
http://www.rcproduct.in/ready-to-fly-rtf/18-hobbyking-fp100-24ghz-4ch-micro-helicopter-mode-2-rtf.html (http://www.rcproduct.in/ready-to-fly-rtf/18-hobbyking-fp100-24ghz-4ch-micro-helicopter-mode-2-rtf.html)


(http://www.rcproduct.in/72-thickbox_default/hobbyking-fp100-24ghz-4ch-micro-helicopter-mode-2-rtf.jpg)

Thanks

Turnigy 4206 530kv Brushless Multi-Rotor Motor
This motor includes a collet style prop adaptor for use with many different style props featuring a 5mm shaft. It also includes a bolt-on cross mount for quick and easy installation on your quadcopter frame.

This is not a modified airplane outrunner. It was designed from the ground up specifically for multi-rotor applications.

Specs:
Kv: 530rpm/v
Can size: 45mm
Shaft: 3.17mm (includes prop adapter for 5mm prop mounting)
Motor Mount Holes: 16mm / 19mm
Suggested ESC: 25A
Rated Watts: 130W
Weight: 68g
Cell count: 3~4S Lipoly
Motor wire length: 390mm

BUY IT:-
http://www.rcproduct.in/multi-rotors-parts/24-turnigy-4206-530kv-brushless-multi-rotor-motor.html (http://www.rcproduct.in/multi-rotors-parts/24-turnigy-4206-530kv-brushless-multi-rotor-motor.html)

(http://www.rcproduct.in/96-thickbox_default/turnigy-4206-530kv-brushless-multi-rotor-motor.jpg)

Hi...Everyone...

Our Website is Under MAINTENANCE

IN ORDER TO PERFORM WEBSITE MAINTENANCE, OUR ONLINE STORE WILL BE TEMPORARILY OFFLINE. WE APOLOGIZE FOR THE INCONVENIENCE AND ASK THAT YOU PLEASE TRY AGAIN LATER.

will be Online very soon..

Contact us - rcproduct.in@gmail.com

DIY Round Tube Motor Mount (12mm Tube)
This is a great DIY round Tube motor mount for 12mm tubes.

This is a great DIY round Tube motor mount for 12mm tubes, it comes with all necessary hardware for mounting and can accommodate a large range of motors.

Specs:
weight: 7g
Size: 63x35x17mm
tube: 12mm
Motor mounting: Slots from 28mm to 11mm

Includes:
One Mount

BUY IT NOW:-
http://www.rcproduct.in/multi-rotors-parts/23-diy-round-tube-motor-mount-12mm-tube.html (http://www.rcproduct.in/multi-rotors-parts/23-diy-round-tube-motor-mount-12mm-tube.html)

(http://www.rcproduct.in/82-thickbox_default/diy-round-tube-motor-mount-12mm-tube.jpg)

Afro ESC 30Amp Multi-rotor Motor Speed Controller
(SimonK Firmware)

Developed from the ground up, we wanted to build a truly Multi-rotor specific ESC that would offer the best performance and value in the market today. We wiped the slate clean and looked to the community for inspiration and help in designing an ESC that truly could be known as “The Multi-rotor ESC”

Enter Simon and Hamasaki AKA SimonK and timecop. This combination of hardware and firmware expertise in conjunction with the Hobbyking in house engineering team gave us the edge needed to develop an ESC like no other and hence the Afro series was born.

Boasting high efficiency, all N-channel MOSFET design, jitter-free hardware PWM input, and smooth power response the Afro ESC series are set to change the expectations of multi-rotor pilots around the globe. The Afro ESC series ship with multi-rotor specific SimonK software preloaded! No need to reflash. For added convenience the Turnigy USB linker can be used via the PWM signal lead for any future software updates eliminating the need for complicated flashing jigs or the need to cut open the heat shrink.

MikroKopter I2C compatibility has also been built in as standard. A DIY port is available under the shrink wrap which allows using the ESC with MikroKopter hardware that uses I2C control.

 Specs:
Current Draw: 30A Continuous
Voltage Range: 2-4s Lipoly
BEC: 0.5A Linear
Input Freq: 1KHz
Firmware: afro_nfet.hex
Discharge wire/plugs: 16AWG/Male 3.5mm
Motor wire/plugs: 15AWG/Female 3.5mm
Weight: 26.5g (Included wire, plug, heat shrink)
Size: 50 x 25 x 11mm

Note: A user manual is available under the files tab, these are no ordinary ESCs! Please take the time to read the manual before using them.

Royalties paid on each unit sold to SimonK and Hamasaki for their design work, without which the Afro ESC would never have been born, thanks guys!

BUY IT:-
http://www.rcproduct.in/all-speed-controllers/24-afro-esc-30amp-multi-rotor-motor-speed-controller-simonk-firmware.html (http://www.rcproduct.in/all-speed-controllers/24-afro-esc-30amp-multi-rotor-motor-speed-controller-simonk-firmware.html)

(http://www.rcproduct.in/83-thickbox_default/afro-esc-30amp-multi-rotor-motor-speed-controller-simonk-firmware.jpg)