Its been a long long time since i flew my quad. I was really enjoying it and learning to do FPV. But then i had a crash and since then its been a long long time. So i thought to utilize this time and make a new frame for FPV use and make it light weight too :giggle:
Also this time i was thinking to make the frame foldable so that i can store it easily ;)
So here is the new SpiderX frame pictures, let me know your views about it.
It is made using Glass Fiber Plates 1.5mm thick and 13mm x 13mm aluminium booms.
looks amazing brother
Hey guys, finally i got time to work on my frame and here is the result
http://www.youtube.com/watch?v=Nr6U-icSImk
13mm aluminum booms
1.5mm Glass Fiber
Red Leopard 2835 KV850 BL Motor (http://www.rcecho.com/LEOPARD-Model-2835-KV850-RC-Outrunner-Brushless-Motor-and-Propeller-Adaptor.html)
F30A with simonk ESC (yet to arrive)
KK2.0 with 1.6 FW
5.8 Ghz 200mW FPV with Clover Leaf Antenna specially tuned for channel 3 (i got it specially made for me)
And yes FPV
as its made using 1.5mm GF sheets its bit flexible at the center but i am planning to add few more sheets at the center, i think it may break in case of hard crash.
Let me know guys how is it?
what is that green thing in between the arms and the frame ?
Its a cricket bat grip i added that to remove some vibration that is generated by motors. I got this idea from Dharmik bhai, he has used this in his frame. I did used this in my previous frame.
I am not going to tight the screws completely, just little bit and going to using thread locker on the screws.
did it work ?
even i want to try it out
yes offcourse, i am using single layer. You can use double layer and try. It adds more flexibility to the frame.
With my previous frame w/o grip it used to be like a one single piece or you can say very stiff. But with grip added i could feel the flexibility.
Should give a try.
Only tilt mount for cam sir? no pan?
No Pan, i dont like pan just tilt suits me :D
How do you colour the alluminium?
oh thank you sir for the advice!
Quote from: lastRites on August 03, 2013, 11:21:49 PM
How do you colour the alluminium?
I bought them pre colored.
@aditya You are welcome, but we should thank Dharmik bhai for this idea. If you are planning to try this then try with dual layer grip, and let us know how it went. :thumbsup:
Nice build Satya bro. Looks perfect. Waiting for the fpv video. I am stuck with the rain :/
Same here bro, rains are keep me inside. There is still some time for maiden for this new frame. I will spend more time on balancing frame and props (unlike my last frame :D )
how is FW 1.6?? i did checked your video what are the improvements?
I got my f30a and new kk 2.0 LCD board. Will flash f30a with simonk and test it out soon.
BTW anyone can tell me which firmware does kk board comes with or how can we check the firmware of kk board.
Satya bro KK2 comes with v1.2 pre loaded. You will see flash screen when power up the board.
Thanks dharmik bhai :thumbsup:
All done, here is my new quad with new X frame.
http://www.youtube.com/watch?v=uVsU1A9CHFM
I am waiting for a sunny day for a maiden and PI tuning.
only new thing in this frame than prior are:
New Motors
New ESC with simonK
New FW on kk2.0 board
Looks cool.. Why you changed the motors? leopard?
:giggle: well i loved DT750 a lot just more than anyone could.
But due to its motor mount and the screw that holds the motor on the mount (mine used to get loosened up after couple of flights) i had to find a replacement. But still i just love DT750 they are awesome 1100grams thrust @17-18 amps thats AWESOME once i got 13 mins flight time with fully charged 4000 mah lipo
And i wanted to decrease the frame weight, mainly i wanted to use 13 mm aluminum booms. Earlier it was 1600-1700 with FPV and now its just 1500~ with FPV
I will down the line or early next year build one more frame, with our quadkopters CNC frame :D with that i will use DT750 motors. :D
DT700s with 12inch props are good if you want a stable frame with LOTS of lift ;D
did maiden today :D was fantastic really SimonK ESC do wonders to quad. I could easily see the smoothness in movements. I did not tune the PI values flew with stock settings, was not in a mood to let rain gods spoil my mood :D
I flew for around 10-13 mins not very sure about that but it was good test flight.
Now i have a question, i have flashed my ESC with simonk but i hear the normal beeps with esc i connected to KK board. I am not very sure but i did found a video long time back which said that the start up beeps changed when ESC has SimonK FW
Can you anybody confirm this please... :help:
Mine gives different tone and there are no functions left to adjust. Only throttle calibration that we can adjust. Which firmware you have flashed?
yea same with me only throttle calibration. bs_nfet.hex firmware i have F30A
Can you share the tone, of your ESC.
Sure i will upload video tomorrow.
http://www.youtube.com/watch?v=DIupX3nz_Ek
maiden fpv with LOS and FPV flying
cool satya bhai... what is the configuration?
Quote from: satyagupta on August 03, 2013, 08:21:07 PM
13mm aluminum booms
1.5mm Glass Fiber
Red Leopard 2835 KV850 BL Motor (http://www.rcecho.com/LEOPARD-Model-2835-KV850-RC-Outrunner-Brushless-Motor-and-Propeller-Adaptor.html)
F30A with simonk ESC (yet to arrive)
KK2.0 with 1.6 FW
5.8 Ghz 200mW FPV with Clover Leaf Antenna specially tuned for channel 3 (i got it specially made for me)
And yes FPV
This is the config.
oh sure forgot to see the page number
Hi Satya, that is super cool FPV set up.
can you please post link from where i can buy the video Tx-Rx & camera?
Are you using fpv goggles ? if so can you pleas post link for that too?
Thank you,
Atul
Thanks Atul,
You can find all FPV related products in my webstore here (http://www.quadkopters.com/product_category/fpv-kit-and-accessories/)
It looks real stable satya bhai.. :)
awesome... :)
Thanks Arun :salute: i will do a lot more learning then will go with goggles.
Nice work Satya bro, i see no vibes which is really cool.
Thank you Dharmik bhai your words means a lot :)
Good work satya bhai...............
Looks very stable................
:hatsoff: :hatsoff: Thanks Shauvik, the secret lies in SimonK ESC and 1.6FW i guess
I have been working on this frame from March-April. i did lots of reading and digging before i actually built it. Hence the lot of time spend before work is paid off.
I have plans to practice more flying with LCD and then with goggles and once i am good, i will go to near by scenes to do some fotugraphy/viodegraphy :D :giggle:
http://www.youtube.com/watch?v=O8tlmV-hvmY
Night flying, trying to capture awesome color in skies.. And a crash in the end :giggle:
Night bird Eating Dust now... :(
Good attempt and nice flying.. Any serious damage looks ok...
nothing serious just both the front arms are done, i have a replacement for now but they are not so good. have order 10 sets from China i will get them by next week or 10 days :D
Its been very very long time since i worked or spend any time on my quads.
I became father in November 2013, so lot of time was spent with baby. And then QK handling webstore is not easy :phew: and also a full time job.
So i never really got to spent some time with my hobby, i did built/flew one but never really spent a lot of time into it. And lately i had started missing that fun. So now i have decided that atleast 2 weekends of a month i would give time to hobby :)
And i have started from today, i am modifying this frame of mine. The design and layout would but same but instead of aluminum booms i am planning to use 15x15 square CF rods (square) and 1.5mm CF sheets for the body.
I got the sheets and the rod couple of days back i would get the CNC ready and do some cutting tomorrow and post some pictures soon :thumbsup:
Sir great Quad...
In the previous video was the video a downlink from the board camera or any HD camera?
Frame looks great,
and nice work too,are you guyz willing to put it on your website any time soon???
Quote from: Himadri Roy on April 25, 2015, 10:10:33 PM
Sir great Quad...
In the previous video was the video a downlink from the board camera or any HD camera?
HD WING camera from HK
http://www.hobbyking.com/hobbyking/store/__17200__HD_Wing_Camera_1280x720p_30fps_5MP_CMOS.html (http://www.hobbyking.com/hobbyking/store/__17200__HD_Wing_Camera_1280x720p_30fps_5MP_CMOS.html)
Thanks Shyam, this is my custom design i am not willing to sale this frame. Requires a lot of effort and time to make just one frame
BTW guys where can i get wire mesh in India? any LHS keeping this?
I need just few meters.
Gunnu selling on this forum