RC India
Welcome Guest, please login or register.
 
Pages: [1]   Go Down
0 Members and 1 Guest are viewing this topic. Topic Tools Topic Tools 
Read
« on: July 15, 2014, 12:44:48 AM »
karsid
Plane Lover
Active Member
**

Reputation Power: 2 
karsid has no influence.
Offline Offline

City: Hyderabad
State: Andhra Pradesh
RC Skills: Beginner
Posts: 73
Join Date: May, 2014




Hi Experts,

i am a beginner here and apologize for this noob question. i have purchased this RCB6i transmitter from rcbazaar a while ago. i tried to bind the receiver with the transmitter as given in the below video.



the video shows that after a successful bind the LED stays solid RED. However, in my case i see that the LED flashes 3 times and then comes back to blink. i tried this even after changing the batteries in the TX and Lipo battery as well on the receiver side. but no change.

What am i doing wrong?


Thanks
KarSid
Logged
 

Read
« Reply #1 on: July 15, 2014, 10:22:29 AM »
KineticHobbies
Plane Lover
Active Member

**

Reputation Power: 2 
KineticHobbies has no influence.
Offline Offline

City: Mangalore
State: Karnataka
RC Skills: Intermediate
Posts: 86
Join Date: Mar, 2014



Try keeping the receiver far away from the TX. If the receiver wire is too close to transmitter antenna, binding fails many times.
Logged

 

Read
« Reply #2 on: July 15, 2014, 05:34:36 PM »
sundaram
FAN OF FPV FLYING, AERIAL PHOTOGRAPHY & MICRO RC
Plane Lover
Forum Hero

*****

Reputation Power: 38 
sundaram is working their way up.sundaram is working their way up.sundaram is working their way up.
Offline Offline

City: Gandhinagar
State: Gujarat
RC Skills: Advanced
Posts: 3407
Join Date: Nov, 2009



Just release the bind button Immediately after connecting battery. If you keep it pressed it does not bind.
Logged

 

Read
« Reply #3 on: July 16, 2014, 02:25:05 PM »
jonboy20
Plane Lover
Active Member
**

Reputation Power: 1 
jonboy20 has no influence.
Offline Offline

City: Mumbai
State: Maharashtra
RC Skills: Intermediate
Posts: 30
Join Date: Aug, 2010



I had taught that I had a similar problem.......But after switching OFF the TX and RX after the BIND procedure  and restarting the same, the receiver light remained solid RED and all the servos and ESC (throttle) worked fine. This showed that the transmitter and Receiver were bound to each other.....Try it out, lets know the result!!
Logged
 

Read
« Reply #4 on: July 20, 2014, 10:56:30 PM »
karsid
Plane Lover
Active Member
**

Reputation Power: 2 
karsid has no influence.
Offline Offline

City: Hyderabad
State: Andhra Pradesh
RC Skills: Beginner
Posts: 73
Join Date: May, 2014



Thanks all for the replies. i have been able to fix the issue by resetting the ID in the radio and trying afresh. However, now i have a strange problem. i using EMAX 4 in 1 ESC and i have no throttle control. while i raise the throttle and cross about 50% or so, the motor powers on at full speed and then there is no control whatsoever on the throttle stick movement. i have tried testing the control using a servo tester and i have perfect speed control from MIN to MAX. So ESC calibration is not the issue here. Any ideas what is the  problem?
Logged
 

Pages: [1]   Go Up
Jump to:  

Related Topics
Subject Started by Replies Views Last post
glitch in avionic rcb6i
Multirotors
karan.k 4 4290 Last post October 31, 2013, 06:08:17 PM
by karan.k
what do i need as simulator for avionic rcb6i?
Radios and Receivers
roby 0 2826 Last post January 05, 2014, 08:05:24 AM
by roby
Avionic RCB6i binding Issue
Multirotors
karsid 0 1480 Last post July 15, 2014, 12:42:50 AM
by karsid
Avionic rcb6i transmitter receiver - Binding Process and requirements
Beginners Zone
Vishal RC 5 6393 Last post February 17, 2015, 02:24:16 PM
by rcrcnitesh
Trouble binding RCB6i transmitter and receiver
Beginners Zone
pankajlal 8 5650 Last post April 09, 2018, 12:51:03 AM
by Raviraj